background image

 

ASSEMBLY PROCEDURE:

 

 

STEP 1: 

 
To  begin  installing  the  ARTPC-
SB2M Mounting Bracket in your 
Artisan  cart,  you  must  first  re-
move  the  appropriate  existing 
shelf unit out of it. 
 
 
This is accomplished by remov-
ing the 4 screws and lock wash-
ers  located  under  the  shelf  on 
both the sides of it.  
(See Figure # 1) 
 
 
 

NOTE  1:

 The ARTPC-32 shown 

in  this  drawing  is  for  illustration 
purposes  only.  These  same  in-
structions  apply  to  all  Artisan 
cart models. 
 
 

NOTE  2: 

The ARTPC-SB2M Bracket can be mounted to the left or right side of the cart. For illustration purposes, 

the assembly will be shown on the right side of the cart 
 
 
 
 

STEP 2: 

 
Install  the  ARTPC-SB2M  Main 
Bracket  assembly  (item  10  - 
part  510-1243  shown  on  page 
2)  by  using  the  proper  screws  
provided. 
 

IMPORTANT: 
 

Install  the  1/4-20 

FLAT

  head 

screws on the TOP and the 1/4-
20 

TRUSS

  head  screws  at  the 

BOTTOM. 
 
Tighten  screws  while  aligning 
the  mounting  bracket  to  the 
sides  and  top  edges  of  the  cart 
unit’s side panel. 
(See Figure # 2) 
 
 
 
 
 
 
Install one of the provided grommets to protect the gas line to be installed at a later stage. 

EXISTING SHELF 

SCREWS 

AND 

WASHERS 

Figure # 1 

1/4-20 TRUSS HEAD 
SCREWS 

1/4-20 FLAT HEAD 
SCREWS 

GROMMET 

Figure # 2 

BACK 
BRACKET 

Summary of Contents for ARTPC-SB2M









Reviews: