manualshive.com logo in svg

Artesyn MVME7616E Series, Installation And Use Manual

Share
Download
Artesyn MVME7616E Series Installation And Use Manual Download Page 51

Connector Pin Assignments

MVME7616E Transition Module Installation and Use (6806800A43F)

51

4.7.4

PMC I/O, 5-Row P2 Adapter (J3)

The PMC I/O connector on the 5-row DIN backplane P2 Adapter is a 64-pin connector, J3. The 
pin assignments and signal mnemonics for this connector are listed in 

Table 4-10

.

Table 4-10 PMC I/O Connector (5-Row P2 adapter)  

Pin

Signal

Signal

Pin

1

GND

GND

33

2

PMCIO0

PMCIO16

34

3

GND

GND

35

4

PMCIO1

PMCIO17

36

5

GND

GND

37

6

PMCIO2

PMCIO18

38

7

GND

GND

39

8

PMCIO3

PMCIO19

40

9

GND

GND

41

10

PMCIO4

PMCIO20

42

11

GND

GND

43

12

PMCIO5

PMCIO21

44

13

GND

GND

45

14

PMCIO6

PMCIO22

46

15

GND

GND

47

16

PMCIO7

PMCIO23

48

17

GND

GND

49

18

PMCIO8

PMCIO24

50

19

GND

GND

51

20

PMCIO9

PMCIO25

52

21

GND

GND

53

22

PMCIO10

PMCIO26

54

23

GND

GND

55

Summary of Contents for MVME7616E Series

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands