manualshive.com logo in svg

Artesyn MVME7616E Series, Installation And Use Manual

Share
Download
Artesyn MVME7616E Series Installation And Use Manual Download Page 17

General Information

MVME7616E Transition Module Installation and Use (6806800A43F)

17

1.7

Five-Row P2 Adapter (MVME761-011)

The P2 adapter for the MVME761-011 mounts onto a 5-row, 160-pin P2 backplane connector. 
The 68- pin female connector, J1, carries 16-bit SCSI signals from the host VMEmodules. It also 
has a 64-pin male connector, J3, for PMC I/O.

This P2 adapter, and the cable for connecting to the MVME761 transition module, can be 
ordered separately as model MVME761P2-011.

1.8

Connectors and Cables

The connectors on the MVME761 transition module and the P2 adapters are listed in the 
following tables. The port connectors are located on the front panel, which is shown in 

Figure 

1-1

. See 

Table 1-5 on page 19

 for a list of the cables. See 

Chapter 4, 

Connector Pin Assignments

.

The cable used for connecting the MVME761 transition module to the P2 adapter is provided 
with the MVME761-0x1

Figure 1-3

Five Row P2 Adapter

J5

2
1

1

64
63

+

U1

9

25

17

CR1

R4

C8

C9

U3

P1

1

32

2
1

64
63

J1

J3

J4

1

U2

9

25

17

+

1

33

D
C
B
A
Z

D
C
B
A
Z

Summary of Contents for MVME7616E Series

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands