manualshive.com logo in svg

Artesyn MVME7616E Series, Installation And Use Manual

Share
Download
Artesyn MVME7616E Series Installation And Use Manual Download Page 41

Chapter 4

MVME7616E Transition Module Installation and Use (6806800A43F)

41

Connector Pin Assignments

4.1

Overview

This chapter provides the pin assignments for the P2 connector and front panel port 
connectors on the MVME761 transition module, as well as for the SCSI and PMC I/O connectors 
on the P2 adapters.

4.2

P2 Connector

Signaling and power from the host VMEmodules are received through connector P2, a 64-pin 
DIN connector. Because the P2 adapter reroutes some of the signals, connector P2 on the 
MVME761 transition module is not pin-for-pin compatible with connector P2 on the host 
VMEmodules.

The pin assignments and signal mnemonics for the MVME761 transition module P2 connector 
are listed in the following table.

Table 4-1 P2 Connector Pin Assignments  

Row A Pins

Row C Pins

Pin

Signal

Pin

Signal

1

C- (R- for RJ-45 J9)

1

C+ (R+ for RJ-45 J9)

2

T-

2

T+

3

R-

3

R+

4

+12VF

4

PRSTB#

5

GND

5

PRD0

6

PRD1

6

PRD2

7

PRD3

7

PRD4

8

PRD5

8

PRD6

9

PRD7

9

GND

10

PRACK#

10

GND

11

PRBSY

11

PRPE

12

PRSEL

12

INPRIME#

13

PRFAULT#

13

GND

Summary of Contents for MVME7616E Series

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands