manualshive.com logo in svg

Artesyn MITX-CORE-820, Installation And Use Manual, Page: 86 / 133

Share
Download
Artesyn MITX-CORE-820 Installation And Use Manual Download Page 86

BIOS

MITX-CORE-820 Installation and Use (6806800M10H)

85

5.4.2.4

Peripheral Configuration

5.4.2.5

HDD Configuration

C7s-State

Enables processor idle power saving C7s state. If enabled, BIOS 
will report C7s instead of C7 to OS.

Table 5-9 Processor Power Management Field Description 

Field

Description

Table 5-10 Peripheral Configuration Field Description

Field

Description

Spread Spectrum Clock

Enables clock chip spread spectrum feature.

PCIe SR-IOV Support

Sets IO virtualization.

Table 5-11 HDD Configuration Field Description  

Field

Description

SATA Device

Enables/Disable sSATA device.

Interface Combination

Selects the SATA controllers operation mode.

RAID Alternate Device ID

Changes the device ID to 292X from 282X in RAID mode to 
prevent the IMSM driver from loading on the platform.

Software Feature Mask Config

Software Feature Mask Config. See 

Software Feature Mask 

Configuration

.

Serial ATA Port 0 / Hard Disk 0

Displays the identity of the device attached.

Serial ATA Port 1 / Hard Disk 1

Displays the identity of the device attached.

Serial ATA Port 2 / Hard Disk 4

Displays the identity of the device attached.

Serial ATA Port 3 / Hard Disk 5

Displays the identity of the device attached.

Summary of Contents for MITX-CORE-820






































































































































Reviews:

No comments