manualshive.com logo in svg

Artesyn ATCA-F140, Installation And Use Manual

Share
Download
Artesyn ATCA-F140 Installation And Use Manual Download Page 29

Hardware Preparation and Installation

ATCA-F140 Installation and Use (6806800M67J)

29

2.4

Rear Transition Modules

If applicable, install a rear transition module. For more information, see the 

RTM-ATCA-F140 

Installation and Use

. You can obtain an electronic copy of the manual from our web site:

1. Go to 

www.artesyn.com

 

2. Under Resources, click Technical Documentation.

3. Enter the publication number or the complete name of the product in the Search box. 

Refer to 

Related Documentation

 

on page 119

 for the list of related documents.

The RTMs are not hot-swappable. Before installation, make sure that no front blade is 
installed in its respective slot, or that the front blade is powered-down. For further details 
about the RTM installation, refer to the installation and use guide of the respective RTM.

Damage of the Product and Additional Devices and Modules

Incorrect installation or removal of additional devices or modules damages the product 
or the additional devices or modules.

Before installing or removing additional devices or modules, read the respective 
documentation and use appropriate tools.

Summary of Contents for ATCA-F140











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands