ARTERY AT32WB415 Series Reference Manual Download Page 73 | Manualshive

Page: 73 / 374

background image

AT32WB415

Series Reference Manual

2022.04.13

Page 73

Ver 2.00

5.7 Flash memory registers

These peripheral registers must be accessed by words (32 bits).

Table 5-4

Flash memory interface

—

Register map and reset value

Register

Offset

Reset value

FLASH_PSR

0x00

0x0000 0030

FLASH_UNLOCK

0x04

0xXXXX XXXX

FLASH_USD_UNLOCK

0x08

0xXXXX XXXX

FLASH_STS

0x0C

0x0000 0000

FLASH_CTRL

0x10

0x0000 0080

FLASH_ADDR

0x14

0x0000 0000

FLASH_USD

0x1C

0x03FF FFFC

FLASH_EPPS

0x20

0xFFFF FFFF

SLIB_STS0

0x74

0x0000 0000

SLIB_STS1

0x78

0x0000 0000

SLIB_PWD_CLR

0x7C

0xFFFF FFFF

SLIB_MISC_STS

0x80

0x0000 0000

FLASH_CRC_ADDR

0x84

0x0000 0000

FLASH_CRC_CTRL

0x88

0x0000 0000

FLASH_CRC_CHKR

0x8C

0x0000 0000

SLIB_SET_PWD

0x160

0x0000 0000

SLIB_SET_RANGE

0x164

0x0000 0000

EM_SLIB_SET

0x168

0x0000 0000

BTM_MODE_SET

0x16C

0x0000 0000

SLIB_UNLOCK

0x170

0x0000 0000

5.7.1

Flash performance select register (FLASH_PSR)

Bit

Abbr.

Reset value

Type

Description

Bit 31: 6

Reserved

0x00000

resd

Kept at its default value.

Bit 5

PFT_ENF

0x1

ro

Prefetch enable flag
When this bit is set, it indicates that the Flash prefetch is
enabled

Bit 4

PFT_EN

0x1

rw

Prefetch enable
0: Prefetch is disabled
1: Prefetch is enabled.

Bit 3

HFCYC_EN

0x0

rw

Half cycle acceleration access enable
0: Disabled
1: Enabled
This bit is used to speed up access to Flash memory when
WTCYC=0.

Bit 2: 0

WTCYC

0x0

rw

Wait states
The wait states depends on the size of the system clock,
and they are in terms of system clocks.
0: Zero wait state
1: One wait state
2: Two wait states
3: Three wait states
4: Four wait states
The system clock sets the wait state on a 32-MHz basis:
Zero wait state for the first 32 MHz
One wait state for the second 32 MHz
Two wait states on the third 32 MHz
Three wait states on the fourth 32 MHz
Four wait states on the fifth 32 MHz.

«
...
71
72
73
74
75
...
»

Summary of Contents for AT32WB415 Series























































































































































































































































































































































































Reviews:

No comments

Related manuals for AT32WB415 Series

Brand: ZOLL Pages: 344

Brand: ABB Pages: 9

Brand: Odom Pages: 19

Brand: MacDon Pages: 30

Brand: Landoll Pages: 52

Brand: Gason Pages: 110

Brand: ZIGBEE Pages: 4

Brand: CAIRE Pages: 38

Brand: Caframo Pages: 72

Brand: M-system Pages: 5

Brand: MA Pages: 2

Brand: MagCore Pages: 80

Brand: MagCore Pages: 80

Brand: Tieline Pages: 359

Brand: RAM Pages: 4

Brand: Airway Pages: 2

Brand: Crazy Foil Pages: 8

Brand: AGCO Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands