ARTERY AT32F425 Series Reference Manual Download Page 263 | Manualshive

Page: 263 / 429

background image

AT32F425

Series Reference Manual

2022.03.30

Page 263

Ver 2.01

14.6.3.5 TMR break function

When the break function is enabled (BRKEN=1), the CxOUT

和

CxCOUT are jointly controlled by OEN,

FCSODIS, FCSOEN, CxIOS and CxCIOS. But, CxOUT and CxCOUT cannot be set both to active level
at the same time. Please refer to 14-17 for more details.
The break souce can be the break input pin or a clock failure event. The polarity is controlled by the
BRKV bit.
When a break event occurs, there are the following actions:



The OEN bit is cleared asynchronously, and the channel output state is selected by setting the

FCSODIS bit. This function works even if the MCU oscillator is off.



Once OEN=0, the channel output level is defined by the CxIOS bit. If FCSODIS=0, the timer

output is disabled, otherwise, the output enable remains high.



When complementary outputs are used:

―

The outputs are first put in reset state, that is, inactive state (depending on the polarity). This
is done asynchronously so that it works even if no clock is provided to the timer.

―

If the timer clock is still active, then the dead-time generator is activated. The CxIOS and
CxCIOS bits are used to program the level after dead-time. Even in this case, the CxIOS and
CxCIOS cannot be driven to their actival level a the same time. It should be note that because
of synchronization on OEN, the dead-time duration is usually longer than usual (around 2
clk_tmr clock cycles)

―

If FCSODIS=0, the timer releases the enable output, otherwise, it keeps the enable output; the
enable output becomes high as soon as one of the CxEN and CxCEN bits becomes high.



If the break interrupt or DMA request is enabled, the break statue flag is set, and a break
interrupt or DMA request can be generated.



If AOEN=1, the OEN bit is automatically set again at the next overflow event.

Note: When the break input is active, the OEN cannot be set, nor the status flag, BRKIF can be

cleared.

Figure 14-98

Example of TMR break function

CxORAW

Delay

Delay

Delay

CxEN

CxCEN

CxIOS

CxCIOS

CxCOUT

CxOUT

BRK

AOEN

14.6.3.6 TMR synchronization

The timers are linked together internnaly for timer synchronization. Master timer is selected by setting
the PTOS[2: 0] bit; Slave timer is selected by setting the SMSEL[2: 0] bit.
Slave modes include:

Slave mode: Reset mode

The counter and its prescaler can be reset by a selected trigger signal. An overflow event
can be generated when OVFS=0.

«
...
261
262
263
264
265
...
»

Summary of Contents for AT32F425 Series














































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AT32F425 Series

System x3630 M4

Brand: IBM Pages: 7

Brand: Octavo Pages: 28

Brand: Obihai Pages: 2

Brand: Accuphase Pages: 2

Brand: ADTRAN Pages: 2

AMB-VDX3H1 Series

Brand: Acrosser Technology Pages: 4

Brand: Accusys Pages: 34

Brand: Digitus Pages: 8

Brand: Renesas Pages: 941

Brand: Omron Pages: 432

Brand: 2N Telekomunikace Pages: 67

Brand: Aviosys Pages: 77

Brand: Holtek Pages: 280

Blend PRO BP-2002

Brand: FOLSOM Pages: 89

Brand: PACOM Pages: 16

Brand: Motorola Pages: 376

Brand: Motorola Pages: 20

StorageGRID Webscale SG5700 Series

Brand: NetApp Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands