ARTERY AT32F413 Series Reference Manual Download Page 189

  AT32F413

 

Series  Reference  Manual

 

2022.06.27

 

Page 189 

 

Rev 2.00

 

 

PWM mode: 

Set CxOCTRL=3’b110/111 to enable PWM mode. Each channel can be   

independently configured to output one PWM signal. In this case, the period of the output signal 
is configured by the TMRx_PR register, and the duty cycle by the CxDT register. The counter 
value is compared with the value of the TMRx_CxDT register, and the corresponding level signal 
is sent according to the counting direction. For more information on PWM mode A/B, refer to the 
description of the CxOCTRL[2: 0] bit. In up/down counting mode, the OWCDIR bit is used to 
indicate the counting direction. 

 

Forced output mode:

 Set CxOCTRL=3’b100/101 to enable forced output mode. In this case, 

the CxORAW is forced to be the programmed level, irrespective of the counter value. Despite 
this, the channel flag bit and DMA request still depend on the compare result. 

 

Output compare mode:

 Set CxOCTRL=3’b001/010/011 to enable output compare mode. In this   

case, when the counter value matches the value of the CxDT register, the CxORAW is forced 
high, low or toggling. 

 

One-pulse mode

This is a particular case of PWM mode. Set OCMEN=1 to enable one-pulse   

mode. In this mode, the comparison match is performed in the current counting period. The 
TMREN bit is cleared as soon as the current counting is completed. Therefore, only one pulse is 
output. When configured as in upcounting mode, the configureation must follow the rule: 
CVAL<CxDT≤PR; in downcounting mode, CVAL>CxDT is required. 

 

Fast output mode:

 Set CxOIEN=1 to enable this mode. If enabled, the CxORAW signal will not   

change when the counter value matches the CxDT, but at the beginning of the current counting 
period. In other words, the comparison result is advanced, so the comparison result between the 
counter value and the TMRx_CxDT register will determine the level of CxORAW in advance. 

Figure  14-16

 

gives an example of output compare mode (toggle) with C1DT=0x3. When the counter 

value is equal to 0x3, C1OUT toggles. 

Figure 14-17

 

gives an example of the combination between upcounting mode and PWM mode A. The 

output signal behaves when PR=0x32 but CxDT is configured with a different value. 

Figure 14-18

 

gives an example of the combination between up/down counting mode and PWM mode 

A. The output signal behaves when PR=0x32 but CxDT is configured with a different value. 

Figure  14-19

 gives an example of the combination between upcounting mode and one-pulse PWM 

mode B. The counter only counts only one cycle, and the output signal sents only one pulse. 

Figure 14-16

 

C1ORAW toggles when counter value matches the C1DT value

 

0

1

2

3

...

31

32

0

1

2

3

...

31

32

0

1

2

3

COUNTER

31

32

0

1

...

PR[15:0]

C1ORAW

TMR_CLK

0

DIV[15:0]

32

011

C1OCTRL

[2

0]

3

C1DT[15

0]

 

Summary of Contents for AT32F413 Series


















































































































































































































































































































































































Reviews: