background image

11 

SPECIFICATIONS 

Input Connections 

 

XLR, 1/4” TRS, balanced 

Output Connections 

 

1/4” TS, unbalanced 

Frequency Response 

 

10Hz to 40kHz, +0/-0.5dB 

Crossover Frequency Range 

 

250Hz to 6kHz 

Subwoofer Frequency Range 

 

50Hz to 250Hz 

Crossover Filter Type 

 

Fourth-order Linkwitz-Riley, 24dB/octave 

Subwoofer Filter Type 

 

Two-pole Butterworth, 12dB/octave 

Dynamic Range 

 

>114dB 

Signal to Noise Ratio 

 

>95dB, Ref: 0dBu, 20Hz-20kHz, unweighted 

Input Impedance  

 

100k Ohms 

Output Impedance  

 

220 Ohms 

Maximum Input Level 

 

+21dBu 

Maximum Output Level 

 

+21dBu 

Total Harmonic Distortion (THD)   

<0.01% (20Hz-20kHz, 0dBu) 

Maximum Gain 

 

+4dB 

Power Requirements 

 

110-125V AC, 50-60hz, 15W (USA) 

 

 

Export units configured for country of destination 

Dimensions (HWD) 

 

1.75” x 19” x 5” 

 

 

44mm x 483mm x 127mm 

Weight 

 

6.2 lbs. (2.8 kg) 

ART maintains a policy of constant product improvement. ART reserves the right to make changes in 

design or make additions or improvements to this product without any obligation to install these 

changes on products previously manufactured. Therefore, specifications are subject to change 

without notice. 

Summary of Contents for CX311













Reviews: