Art-Tech F-14

WWW.ART-TECH.COM

5

1.

 

Do not disassemble or reconstruct the battery.

2.

 

Do not short-circuit the battery.

3.

 

Do not use or leave the battery nearby the fire, stove or heated place (more than 80

).

4.

 

Do not immerse the battery in water or sea water, do not get it wet.

5.

 

Do not charge the battery under the blazing sunlight.

6.

 

Do not drive a nail into the battery, strike it by hammer or tread it.

7.

 

Do not impact or toss the battery.

8.

 

Do not use the battery with conspicuous damage or deformation

9.

 

Do not charge a warm battery. Allow it to cool completely before attempting to charge.

10. Do not reverse charge or over discharge the battery.
11. Do not connect the battery to the ordinary charger socket or car cigarette jack.
12. Do not use the battery for unspecified equipment.
13. Do not touch the leaking battery directly, please wash your skin or clothes with 
      water if they are bedewed by liquid leaking from the battery.
14. Do not mix the Li-Poly battery with other un-chargeable battery in using.
15. Do not continue charging the battery over the prescribed time.
16. Do not put the battery into the microwave oven or high-pressure container.
17. Do not use the abnormal battery.
18. Do not use or keep the battery under the sunlight.
19. Do not use the battery nearby the place where generates static electricity (over 64V).
20. Do not charge the battery when the environmental temperature is under 0

 or over 45

21. If you find the battery leaking, smelling or abnormal, stop using it and return it to the seller.
22. 
23. Keep the battery away from the children.
24. Use the specified charger and observe charging requirement (under 1A).
25. When using by minors, parents should show them to the correct instruction.

When

 

the

 

battery

 

is

 

charging, please do not make it near the flammable materials!

Safety Instruction of Li-Po/Ni-MH battery

Notification for ESC

1.  The function of this ESC was in the best condition after factory setting; please do not change it by yourself.
2.  Before connecting the battery, please make sure the throttle and Micro-trim were in the lowest position. If 

the throttle and Micro-trim were not in the lowest position by mistake after connecting the battery, you can 
cut off the battery; move the throttle and pitch to the lowest position, then connect the battery.

3.  The ESC of the airplane was in a good cooling position after factory assembly; please do not move its 

position.

4.  The ESC should be connected to the brushless motor correctly, otherwise the motor will be reversed 

turning, and the model airplane can not fly correctly.

Summary of Contents for F-14 "TOMCAT" JET

















Reviews: