background image

* Size rounded off to the nearest foot

BUILDING DIMENSIONS

CAUTION: SOME PARTS HAVE SHARP EDGES. CARE
MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES
TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ
SAFETY INFORMATION PROVIDED IN THIS MANUAL
BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES
WHEN HANDLING METAL PARTS.

715521208

Model No.

697.68221

Owner's Manual & Assembly Instructions

       WR01

                                                                       Exterior Dimensions             Interior Dimensions             Door

       *Approx.       Foundation        Storage Area           (Roof Edge to Roof Edge)              (Wall to Wall)               Opening
           Size               Size             Sq. Ft.  Cu. Ft.        Width      Depth      Height      Width     Depth    Height   Width  Height

        10' x 11'     121" x 131 3/8"       106       628         123 1/4"   133 7/8"     81 3/8"    118 1/4"   128 5/8"  80 1/8"   55 1/2"    60"

3,0m x 3,4m    307cm x 334cm         9,8m

2

    17,8m

3

           313cm       340cm         207cm        300cm       327cm     204cm     141cm   152cm

Summary of Contents for 697.68221



































Reviews: