background image

* Size rounded off to the nearest foot

BUILDING DIMENSIONS

CAUTION: SOME PARTS HAVE SHARP EDGES. CARE
MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES
TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ
SAFETY INFORMATION PROVIDED IN THIS MANUAL
BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES
WHEN HANDLING METAL PARTS.

704740101

Model No.    PM108

VM108

Owner's Manual & Assembly Instructions

       G1

                                                                       Exterior Dimensions             Interior Dimensions             Door

       *Approx.       Foundation       Storage Area           (Roof Edge to Roof Edge)              (Wall to Wall)               Opening
           Size               Size             Sq. Ft.  Cu. Ft.        Width      Depth      Height      Width     Depth    Height   Width  Height

         10' x 8'     121" x 92 3/4"           74        467         123 1/4"    95 1/4"         86"       118 1/4"      90"      84 3/4"   55 1/2" 64 1/2"

3,0m x 2,3m  307cm x 236cm         6,9m

2

     13,2m

3

           313cm        242cm         218cm         300cm       229cm     215cm      141cm   164cm

Summary of Contents for PM108

































Reviews: