Arrow Shark TS-760A Owner'S Manual Download | Manualshive

Page: 3 / 16

background image

Performance Tips

Power Switch Starting

The stock version of the TS760A Starter Kit comes with a polished alloy power switch for

manual starting. You will need to correctly connect all the wires and an 11.1V LIPO

battery to the starter kit according to the following photo:

You can arrange and organize the power wires to any position in your RC vehicle that

best suits your application; make sure though that the location where you store the

battery will not hit the ground should your RC car flip.

«
1
2
3
4
5
...
»

Summary of Contents for TS-760A

















Reviews:

No comments

Related manuals for TS-760A

Brand: 3W Pages: 20

Brand: Onan Pages: 341

Brand: Northern Lights Pages: 42

Brand: Mercury/Mariner Pages: 130

Brand: Mercury Pages: 18

Brand: Mercury Pages: 9

Brand: Mercury Pages: 85

Brand: MerCruiser Pages: 895

Brand: Lombardini Pages: 64

11LD522-3 Series

Brand: Lombardini Pages: 44

Brand: Lombardini Pages: 58

Brand: Lombardini Pages: 68

Brand: Lombardini Pages: 109

Brand: Detroit Diesel Pages: 22

Brand: Yanmar Pages: 316

Brand: MULTIPLEX modell Pages: 6

Brand: DANA Pages: 3

Brand: DANA Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands