manualshive.com logo in svg

Arris C4, User Manual

The DiGidot C4 product offers endless lighting control possibilities. With its advanced features and user-friendly interface, this versatile device allows you to create stunning light shows effortlessly. Download the user manual for free at manualshive.com and unlock the full potential of your DiGidot C4 device.

Share
Download
background image

Chapter 16: Dynamic Routing Protocols 

 

STANDARD Revision 1.0 

C4® CMTS Release 8.3 User Guide 

© 2016 ARRIS Enterprises LLC. All Rights Reserved. 

521 

 

Purpose 

Command 

Logging 

Enables/disables detailed logging. 
This command creates extensive protocol message 
logging. 

trace logging router ospfv3 [no] 

 

 

Routing Information Protocol 

Routing Information Protocol (RIP) is a distance vector routing protocol. Because it learns routes dynamically without 
provisioning, RIP requires little overhead and is easy to implement. It remains a popular routing protocol, especially for 
small networks. 

  Note: The C4/c CMTS does not support RIP version 1 (RIPv1). If the C4/c CMTS is connected to a router that supports only 

RIPv1, problems result because the C4/c CMTS is unable to decipher the information that is communicated by a RIPv1 
router. RIP supports only IPv4. 

 

 

RIP version 2 

RIP version 2 (RIPv2) is compatible with the C4/c CMTS. Unlike RIPv1 it supports subnet masks and Message Digest 5 (MD5) 
authentication. For more information on this standard, see RFCs 2453 and 1058. 

 

 

Hop Count 

RIP uses a single criterion (hop count) for determining the best available route. Each route in a RIP routing table is assigned 
a hop count of 1–16. 

A value of 15 hops is the longest route permitted; once the hop count value reaches 16 the route is considered 
unreachable. 

 

 

Summary of Contents for C4













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for C4

ABB FPBA-01 PROFIBUS DP Quick Installation And Start-Up Manual preview
FPBA-01 PROFIBUS DP
Brand: ABB Pages: 2
ABB ControlMaster CM15 Instructions preview
ControlMaster CM15
Brand: ABB Pages: 4
IBM ServeRAID M5014 User Manual preview
ServeRAID M5014
Brand: IBM Pages: 106
Danfoss VLT 2800 Instruction Manual preview
VLT 2800
Brand: Danfoss Pages: 7
Oceanic DX1 Product Service Manual preview
DX1
Brand: Oceanic Pages: 11
Samson 3372 User Manual preview
3372
Brand: Samson Pages: 8
Samson 3249 Mounting And Operating Instructions preview
3249
Brand: Samson Pages: 60
Samson 2405 Series Mounting And Operating Instruction preview
2405 Series
Brand: Samson Pages: 40
Ultratec SureFire Operation Manual preview
SureFire
Brand: Ultratec Pages: 33
Saluki SMR Series Quick Start Manual preview
SMR Series
Brand: Saluki Pages: 13
Interlogix TruPortal TP-ADD-1DIP Quick Reference preview
TruPortal TP-ADD-1DIP
Brand: Interlogix Pages: 9
Haes ELAN HS-5100 User Manual preview
ELAN HS-5100
Brand: Haes Pages: 42
Seiko G1216B1N000 User Manual preview
G1216B1N000
Brand: Seiko Pages: 30
Waeco ASC G Wi-Fi kit Operating Manual preview
ASC G Wi-Fi kit
Brand: Waeco Pages: 386
Tamiya TLU-02 Quick Start Manual preview
TLU-02
Brand: Tamiya Pages: 5
Delabie PREMIX COMPACT Manual preview
PREMIX COMPACT
Brand: Delabie Pages: 20
Linear Technology LTC3703 Manual preview
LTC3703
Brand: Linear Technology Pages: 32
Anritsu MU120119A Operation Manual preview
MU120119A
Brand: Anritsu Pages: 54

Brands by name

Popular brands

Load more brands