ARRI WRC-1 Instruction Manual Download Page 41

Page: 41 / 196

Pre-defined lens types are:

Display:

Lens set:

ARRI Zeiss Ultra Primes

VAr P

ARRI Zeiss Variable Primes

HS 35

ARRI Zeiss High-speed lenses for 35mm film

Std35

ARRI Zeiss Standard lenses for 35mm film

HS 16

ARRI Zeiss High-speed lenses for 16mm film

User

lens previously defined by the user

• Select the required lens set using the handwheel.

Then press the SEL button. The focal length then
appears in the second line of the display.

• Select the focal length using the handwheel.

Confirm the selection by pressing the SEL button.

• The display now shows the command ‘DO CAL’.

Start the calibration by pressing the CAL button on the
WMU-1

➪

photo

CAL button

Controlling the Iris

Summary of Contents for WRC-1





































































































































































































Search results

Summary of Contents for WRC-1

Reviews:

Related manuals for WRC-1

Brands by name

Popular brands

ARRI WRC-1, Instruction Manual

Search results

Summary of Contents for WRC-1

Reviews:

Related manuals for WRC-1

Brands by name

Popular brands