background image

PowerMaster II RF Wattmeter 

 

 

 

www.arraysolutions.com 

 

 

Rev 4.1 -  February 23, 2017 

Note: This equipment has been tested and found to comply with the 
limits for Class B digital devices, pursuant to Part 15 of the FCC Rules. 
These  limits  are  designed  to  provide  reasonable  protection  against 
harmful  interference  in  a  residential  installation.  This  equipment 
generates,  uses,  and  can  radiate  radio  frequency  energy,  and  if  not 
installed  and  used  in  accordance  with  the  instructions  may  cause 
harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If 
this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and 
on, the user is encouraged to try to correct the interference by one or 
more of the following measures:  
 
 
 
 
 

 
 
 

 

Reorient or relocate the receiving antenna.  

 

Increase the separation between the equipment and receiver.  

 

Connect the equipment into an outlet on a circuit different 
from that to which the receiver is connected.  

 

Consult a qualified radio/TV technician for help.  

Properly shielded and grounded cables and connectors must be used in 
order to meet FCC emission limits. Array Solutions is not responsible 
for  any  radio  or  television  interference  caused  by  using  other  than 
recommended  cables  or  connectors  or  by  unauthorized  changes  or 
modifications  to  this  equipment.  Unauthorized  changes  or 
modifications could void the user's authority to operate the equipment.  

This  device  complies  with  Part  15  of  the  FCC  Rules.  Operation  is 
subject to the following two conditions: (1) this device may not cause 
harmful interferences, and (2) this device must accept any interference 
received, including interference that may cause undesired operation.  

Responsible Party: Array Solutions, Telephone 1(214) 954-7140

Industry Canada Compliance Statement  

This Class B digital apparatus meets the requirements of the Canadian                                  

 Interference-Causing Equipment Regulations.  

Avis de conformité à la réglementation d'Industrie Canada  

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement 

 sur le matériel brouilleur du Canada.  

  

PowerMaster RF Wattmeter Series

 

 
Federal Communications Commission  
(FCC) Statement 

 

Summary of Contents for PowerMaster II





























Reviews: