background image

507838-01

Issue 1813

Page 18 of 19

1

Duct

System

Filter

Integrated Control

Electric Heat Amps

Duct Static

5

Line Voltage

3

RETURN

AIR

SUPPLY

AIR

Temperature

8

Blower Motor Amps

6
7

Thermostat

9

2

4

Drain Line

Disconnect

Switch

ELECTRIC HEAT  AMPS____________

8

8

7

5

DUCT SYSTEM
SUPPLY AIR DUCT
Sealed
Insulated (if necessary)
Registers Open and Unobstructed
RETURN AIR DUCT
Sealed
Filter Installed and Clean
Registers Open and Unobstructed
INTEGRATED CONTROL
Jumpers Configured Correctly (if applicable)
Appropriate Links in Place (if applicable)
VOLTAGE CHECK
Supply Voltage ___________

Electrial Connections Tight

1

2

3

DRAIN LINE
Leak Free

4

TOTAL EXTERNAL STATIC (dry coil)

Supply External Static ______      ______

TEMPERATURE DROP (Cooling Mode)
Return Duct Temperature   ___________

THERMOSTAT
Adjusted and Programmed

Return External Static ______      ______
Total External Static = ______      ______

6

Supply Duct Temperature − ___________

Temperature Drop = ___________

TEMPERATURE RISE (Heating Mode)
Return Duct Temperature   __________
Supply Duct Temperature − __________

Temperature Rise = __________

Operation Explained to Owner

9

Explained Operation of System to Homeowner

Technician’s Name:_______________________Date Start−Up & Performance Check Completed__________

Installing Contractor’s Name_______________________
Installing Contractor’s Phone_______________________
Job Address____________________________________

Installing Date_______________________________
Air Handler Model #___________________________

INDOOR BLOWER AMPS___________
INDOOR BLOWER CFM____________

Low Voltage _____________

dry coil    wet coil

Figure 14. 

Start-Up and Performance Checklist (Upflow Configuration)

Summary of Contents for BCE7E Series




















Reviews: