Armitage Shanks Avon 21 Installation Instructions Manual Download Page 17

REECE PRODUCT QUALITY GUARANTEE

You have purchased a product from Reece Australia Pty Ltd  
ABN 84 004 097 090 (“Reece”). This product is covered by a 
5 year replacement product warranty and a 12 month warranty 
over spare parts and labour.

5 YEAR PRODUCT WARRANTY 

This warranty covers faults in the construction, material and 
assembly of finished products. Products which are within 5 
years from the date of purchase, found upon inspection by an 
authorised Reece representative to be defective in construction, 
material or assembly, will be repaired or exchanged with an 
equivalent product free of charge. Replaced items become 
Reece’s property. 
This warranty also covers any spare parts included under 
“Manufacturer’s Provisions” below.

Manufacturer’s Provisions

The following spare parts are covered by a 10 year warranty:

• 

Mixer Cartridge

ONE YEAR SPARE PARTS WARRANTY

Spare parts other than those listed in the Manufacturer’s 
Provisions above which are within 1 year from the date of 
purchase found upon inspection by an authorised Reece 
representative to be defective in construction, material or 
assembly will be replaced free of charge. Replaced items 
become Reece’s property.

AVAILABILITY OF REPLACEMENT PRODUCTS  
AND SPARE PARTS

All replacement products and spare parts will be available for 
collection without charge to the customer at the nearest Reece 
branch to the customer’s location, or elsewhere as agreed 
between the customer and Reece.

LABOUR

The labour for the replacement of products that are within one 
year from the date of purchase found upon inspection by an 
authorised Reece representative to be defective in construction, 
material or assembly, and in relation to all spare parts to which 
this warranty applies, will be supplied by Reece or the relevant 
supplier using licensed plumbers engaged by Reece or the 
relevant supplier

WARRANTY CONDITIONS

This warranty will apply only under all of the following 
conditions:

•  The item has been installed by a licensed plumber
•  Failure is due to a fault in the manufacture of the product
•  Proof of purchase (including the date of purchase) is    

 provided

•  The installation of the product is in accordance with the  

  instructions provided

•  The product has been installed in valid applications as  

  stated in accordance with the recommended use 

This warranty does not cover products purchased as an  
ex-display without being fully checked and tested for sale  
by the manufacturer.

This warranty does not include faults caused by:

•  Unsuitable or improper use
•  Incorrect installation or installation not in accordance 

 

  with the instructions provided

•  Installation or part installation by any person other than a  
  LICENSED PLUMBER who is suitably qualified to install the  
  product, or a Licensed Electrician where applicable.
•  Normal wear and tear
•  Inadequate or complete lack of maintenance
•  Chemical, electrochemical or electrical influences
•  Harsh detergents or abrasive cleaners used on 

 

  product finishes

EXCLUSIONS

To the fullest extent permitted by law, Reece excludes all liability 
for damage or injury to any person, damage to any property, 
and any indirect consequential or other loss or damage.

CLAIM PROCEDURE

For all warranty queries customers are to contact the branch 

where the product was purchased. These details can be found 
on your purchase invoice.  

General contact details for Reece are as follows:

 

Reece Australia Pty Ltd

 

118 Burwood Hwy

 

Burwood VIC 3125

 

+61 3 9274 0000

 [email protected]

The benefits given by this warranty are in addition to the other 
rights and remedies that consumers may have under the 
Australian Consumer Law and any other applicable laws.

Our goods come with guarantees that cannot be excluded 
under the Australian Consumer Law. You are entitled to a 
replacement or refund for a major failure and for compensation 
for any other reasonably foreseeable loss or damage. You 
are also entitled to have the goods repaired or replaced if the 
goods fail to be of acceptable quality and the failure does not 
amount to a major failure.

TAP-ARMITAGE-5

Don’t risk it, use a licensed plumber.

5

YEAR

Q

U

ALIT

Y GUARA

NT

EE

Summary of Contents for Avon 21


















Reviews: