You must be eighteen (18) years of age to purchase any of our electronic
cigarette products.
Complies with relevant European standards.
Armerah eGo-VV Variable Vape Battery with LCD
General Operational Instructions
Please read these instructions very carefully before using this device.
First ensure you have filled your atomiser with your chosen e-liquid and correctly fitted it to your battery. Do not operate when there is no
liquid in the atomiser.
The eGo-VV is a battery with variable voltage settings from 3.0 to 6.0 volts in 0.1 volt increments. It also has a passthrough capability
meaning that it can be used whilst it is connected to a USB port for recharging.
To turn the device on press the main button five times in quick succession (within 3 seconds) from off, the
LCD will display ON momentarily.
Press the main button momentarily (less than 1.5 seconds) and the LCD will display the battery level and the
resistance value in ohms of the atomiser, for example 2.8o. If the display shows “ooo” then there is no
atomiser fitted or the coil is faulty (open circuit) and needs to be replaced. If the LCD displays ”---“ then the
atomiser coil is faulty (short circuit) and needs to be replaced or more likely the battery needs recharging or is
faulty. The light in the main button will also flash three times.
Press the button and hold in to vape whilst inhaling from the mouthpiece, the button will illuminate. Release
the button to stop vaping. Each time the button is pressed and held to vape (more than 3 seconds) the LCD
will illuminate and display the battery level and the number off puffs taken since the last recharge. For best
results hold your e-cigarette by the battery with the mouthpiece uppermost.
To turn the device off press the main button five times from on, the LCD will display OFF. When the button is
pressed while the device is off the LCD will display OFF.
The battery is fitted with a safety cut out feature, if the main button is held in for 10 seconds the device will cut out and the light will flash
approximately 8 times. It can be turned on again after waiting approximately 20 seconds after the button has been released.
If the main button light flashes 10 times when the button is pressed to vape then the battery needs to be recharged.
Switch Main Menu Modes
Turn the device ON then press the main button twice within 1.5 seconds (this is known as Switch Main Menu)
and the LCD will display “x.xU” where x.x is the current voltage value from between 3.0 to 6.0. Press the small
“
+
” button near the display to increase the voltage in 0.1 steps or the “
–
“ button to decrease.
Press the Switch Main Menu sequence twice and the LCD will display “LCD”, press the “
–
“ button and the LCD
will change colour. Repeatedly press the “
–
“ button to scroll through the seven colour options in order which
is white, light blue, purple, yellow, blue, green, red. Repeatedly press the “
+
” button to scroll through in the
opposite direction. Stop on the desired colour to set.
Press the Switch Main Menu sequence three times and the LCD will display “Pxx” where xx is the current
power value from between 05 to 15 watts. Press the small “
+
” button near the display to increase the power
1 watt at a time or the “
–
“ button to decrease.
Press the Switch Main Menu sequence four times and the LCD will display the total number of smoking puffs
in total. When the count reaches 1000 a bar will appear on the left starting from the top and the count will
restart from 0. Four bars represent 4000 meaning the maximum count is 4999, 3206 is shown.
Using with Variable Settings
Results will vary depending on the user style, the atomiser and the e-liquid and it will take some experimentation to achieve the desired
effect. This product is most suitable for use by experienced vapers. Vaping at a higher voltage will drain the battery more quickly than
when using it at a lower setting.
Set at 3.0V gives the mildest vape and throat hit, the 6.0V setting gives the most vapour and strongest throat hit. Our standard batteries
operate at a fixed voltage of around 3.6V, we recommend that you start at this level and then make small adjustments until you find your
own preferred setting. Different atomisers and e-liquids may require different settings to suit your own personal taste.