2
■
WARNING: The power supply is not for use with receptacles that are
weatherproof only when the receptacle is covered (the attachment
plug cap is not inserted and the receptacle cover is closed).
■
WARNING: Risk of electric shock. Mount the power supply at a height
greater than 30 cm / 11.8 in. from the ground surface.
OPERATION
Functions of the remote
■
Pull out the plastic battery barrier sheet from the battery
compartment located on the bottom of the remote.
■
The remote does not require line-of-sight to operate the lights. Range
will vary depending on your building structure and where the receiver
on the tape light is mounted.
■
The remote can operate up to 50 feet in optimal conitions, but each
installation has unique variables that may affect range.
Select from various
fade and strobe
dynamic effects
Incrementally adjust
the brightness of the
lighting up or down
Increase or decrease
the speed of the
selected dynamic effect
Turns lights ON or OFF
Brightness settings
are saved
Quick access to
preset light levels
Pairing multiple kits
The remote in each kit comes paired with the tape light. For larger installations,
multiple kits can be paired together for control by a single remote.
PAIRING
■
Unplug the power supply for the kit that is to be paired.
Wait 5 seconds
■
Restore power to the power supply, then within 10 seconds press and
hold the 50% and the 10% buttons on the remote at the same time
■
The lights will flash to indicate a successful pairing This kit will now
operate with the remote used in this procedure. Repeat as desired
with other kits and remotes.
Each remote
uniquely
paired to a kit
One remote
paired to
multiple kits
NOTE: Dynamic effects will not stay synchronized when one remote is
paired to multiple kits.
TO RETURN TO SINGLE-REMOTE OPERATION
For each kit, perform the following steps using a unique remote:
■
Unplug the power supply for the kit that is to be returned to single-
remote operation.
■
Restore power to the power supply, then within 10 seconds press and
hold the 50% and the10% buttons at the same time (The lights will
flash to indicate the signal has been received)
■
Perform the two steps above a second time to complete the process
This kit will now operate only using the remote used in this procedure.
Repeat as desired with other kits and remotes.
Changing the battery
■
To replace the battery, push in the tab on
the side of the battery tray, and pull the tray
out of the remote. Refer to the instructions
on the back of the remote.
■
Always purchase the correct size and grade
of battery that is most suitable for the
intended use.
■
Ensure the battery is installed correctly with
regard to polarity (+ and –).
■
Remove battery from the equipment when it is not being used for an
extended period of time.
■
Remove used batteries promptly.
■
WARNING: The remote contains a CR2025 DC 3V button battery. If
swallowed, it could cause severe injury or death within 2 hours. Seek
medical attention immediately.
CARE AND CLEANING
■
To clean the light, use a clean dry or slightly damp cloth.
■
Do not use cleaners with chemicals, solvents or harsh abrasives
as damage to the light strip may occur.
TROUBLESHOOTING
The LED strip will not light.
■
The power supply does not have power. Make sure the plug is fully
inserted into a live 120-volt outlet. Check connections and circuit
breaker if direct wiring.
■
The power supply output cable is not properly secured. Check the
connection and make sure that the connector is inserted fully,
and the collar is tightened securely.
■
Batteries in the remote are dead, improperly installed, or the battery
protector has not been removed. Make sure the battery protective strip
is removed. Check that the orientation and type of battery are correct
and that the battery is not depleted.
■
The remote is too far from the receiver. The remote can operate up
to 50 feet in optimal conditions, but each installation has unique
variables that may affect range.
The fuse blows or a circuit breaker trips when the light is turned on.
■
A wire is exposed. Discontinue use of the lamp. Unplug the unit from
the wall. Contact a qualified electrician.
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CUSTOMER SUPPORT
Email: [email protected] | Phone: 410-354-6000
Monday–Friday, 9 a.m.–5 p.m., EST
TWO-YEAR LIMITED WARRANTY
Improper installation, abuse, or failure to use this product for its intended
purpose will void warranty. This warranty only applies when all components,
including LED power supplies, have been provided by or approved for use by
Armacost Lighting. The warranty does not cover labor or any other costs or
expense to remove or install any defective, repaired or replaced products.
© 2022 Armacost Lighting.
All rights reserved.
220201
