7. Select static RGB color
Press the “COLOR+” and “COLOR–” keys to scroll
through the preset library of colors.
8. Shortcut color keys
Press to select preset colors.
9. White brightness control
Press to increase white LED brightness and press
to decrease it.
10. RGB brightness control
Press to increase RGB LED brightness and press
to decrease it.
11. Dynamic effect
Press “MODE+” and “MODE–” to select the
dynamic effect mode and “SPEED+” and
“SPEED–” to adjust the effect speed.
12. Remote indicator
When pressing keys, the indicator blinks if the remote
is working properly. If the indicator flashes slowly
when pressing keys, battery power is low and it needs
to be replaced. Replace with a CR2032 battery.
13. Setting up a Wi-Fi connection
Install the Tuya app to set up a Wi-Fi connection.
Before setup, make sure the controller is in factory
default mode and not connected to other wireless
routers. The controller indicator should glow
yellow before it has been connected to Wi-Fi.
Remote control operation
14. Using the remote control
Pull out plastic battery insulation tab before use.
The RF wireless remote will work through walls
and doors. Do not install in a metal enclosure.
15. Pairing with a new remote control
The remote control and receiver are already paired,
but up to five remotes can be paired to one receiver.
To pair a new remote:
1. Disconnect power to receiver and wait
five seconds.
2. Reconnect power and wait ten seconds.
3. Press the
and
keys simultaneously
for about three seconds until the remote
indicator flashes quickly.
16. De-pairing remotes
To de-pair a remote control, pair the remote you
wish to continue using with the controller and
any other paired remotes will be de-paired.
17. Reset to factory default
To reset the Wi-Fi setting and remote control pairing:
1. Unplug the receiver. Plug in after five seconds.
2. Press the
and
keys simultaneously for
about three seconds, within ten seconds
of the receiver being powered on.
The indicator will flash yellow three times to confirm.
Safety Protection
The controller has a function to prevent it from
being damaged by mis-wiring, output short circuit,
overloading, or overheating. It will automatically
shut down under these extreme conditions until
safe operating conditions are restored. To avoid
shutdowns, make sure the installed LED lighting is
compatible with constant voltage driving, is in the
rated range of the controller, and the cables are well
connected and insulated. Also, install the controller
with proper ventilation and heat dissipation in mind.
Specifications
Output mode ......................................PWM constant voltage
Working voltage ...................................................6–24V DC
Rated output current ...................................4x3A (12A max)
Static colors ........................... 30 (remote) / 16 million (app)
Brightness levels .............................10 (remote) / 100 (app)
Dynamic effect modes ................................ 34 (remote only)
Dynamic speed levels ................................. 10 (remote only)
Color preset keys (remote) ................................................ 7
Scene / Timing function.....................User defined (app only)
Music sensing color ....................................... Yes (app only)
PWM physical grade ...........................................4000 steps
Overload/heat protection ................................................ Yes
Remote frequency .............................................433.92MHz
Remote control range ................... >49 ft./15m in open areas
Wi-Fi standard ......................................... IEEE 802.11a/b/g
Controller dimensions ......................3.43 X 0.95 X 0.59 in./
............................................................... 87 X 24 X 15mm
Remote dimensions .......................3.41 X 1.42 X 0.329 in./
............................................................ 86.5 X 36 X7.5mm
4
5
Customer support
Email: [email protected]
Phone: 410-354-6000
Monday–Friday, 9 a.m.–5 p.m., ET
Warranty
Limited 1-year warranty. This product is for dry
location use only. Improper installation, improper
powering, abuse, or failure to use this device for
its intended purpose will void warranty. Proof of
purchase is required for all returns. Questions?
Email [email protected].
© 2020 Armacost Lighting. All rights reserved.
201001
armacostlighting.com
