manualshive.com logo in svg

ARM V2M-Juno r2, Technical Reference Manual

Share
Download
ARM V2M-Juno r2 Technical Reference Manual Download Page 122

A.1 

Debug connectors

The V2M-Juno r2 motherboard provides one P-JTAG and two trace connectors for debug.

This section contains the following subsections:
•

A.1.1 P-JTAG connector

 on page Appx-A-122

.

•

A.1.2 Trace connectors

 on page Appx-A-123

.

A.1.1 

P-JTAG connector

The V2M-Juno r2 motherboard provides one P-JTAG connector.

The P-JTAG connector also supports 

Serial Wire Debug

 (SWD).

The V2M-Juno r2 motherboard labels the P-JTAG connector as 

CS_JTAG

.

The following figure shows the P-JTAG connector, J25.

1

19

2

20

Figure A-1  P-JTAG connector, J25

The following table shows the pin mapping for the P-JTAG signals on the P-JTAG connector, J25.

Table A-1  P-JTAG connector, J25, signal list

Pin Signal

Pin Signal

1

VTREFC (1V8)

2

CS_BS_VSUPPLY (1V8)

3

nTRST

4

GND

5

TDI

6

GND

7

SWDIO

/

TMS

8

GND

9

SWDCLK

/

TCK

10

GND

11

GND/RTCK

12

GND

13

SWO

/

TDO

14

GND

15

nSRST

16

GND

17

No connection/

EDBGRQ

18

GNDDETECT

19

No connection/

DBGACK

20

GND

 

Note

 

• Pins 9 and 17 have pulldown resistors to 0V.
• Pin 11 has a pulldown resistor to 0V. V2M-Juno r2 motherboard does not support adaptive clocking.
• Pins 3, 5, 7, 13, 15, and 19 have pullup resistors to 1V8.
• Pins 7 and 9 are dual-mode pins that enable the Juno r2 SoC to support both the JTAG and SWD

protocols.

Related concepts

2.17 Debug and trace

 on page 2-59

.

A Signal Descriptions

A.1 Debug connectors

ARM 100114_0200_03_en

Copyright © 2015–2017 ARM Limited or its affiliates. All rights reserved.

Appx-A-122

Non-Confidential

Summary of Contents for V2M-Juno r2























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands