manualshive.com logo in svg

ARM Prospector P1100, User Manual, Page: 83 / 154

Share
Download
ARM Prospector P1100 User Manual Download Page 83

Hardware Description

ARM DUI 0122A

Copyright © ARM Limited 2000. All rights reserved.

3-51

3.16 JTAG interface

The SA-1100 and XCR3128 PLD both contain a JTAG Test Access Port (TAP). The 
SA-1100 supports boundary scan, which can be used to program the flash, and the PLD 
supports in-circuit programming.

Figure 3-15 shows the JTAG data routing in The P1100.

Figure 3-15 JTAG architecture

The P1100 connects the TAP controllers in the SA-1100 and PLD in a daisy chain. The 
JTAG connector is buffered through a 74LCX541 octal buffer. This is a 3-volt device 
with 5-volt tolerant inputs. The scan chain TDI signal is routed to the SA-1100 TAP as 

BUF_JTAG_IN

. The TDO signal 

CPU_TDO

 from the SA-1100 provides the TDI input 

to the XCR3128. The TDO signal from the PLD is then returned to the JTAG interface 
through the buffer. 

The JTAG reset signal has a pull down on the board to minimize power consumption in 
normal use, and a pullup on the cable to ensure correct functioning of Multi-ICE.

A small profile, single row 8-way vertical DF13 type connector (JP18) provides the 
JTAG external interface. An ARM supplied programming utility can be used to 
program the PLD using Multi-ICE. An SA-1100 boundary scan utility is supplied to 
enable you to program the flash. 

Alternatively, Xilinx supply a software utility to download data to the PLD and a 
sample cable design to attach to the parallel port of an IBM PC or compatible. 

SA-1100

System

controller

PLD

Multi-ICE connector

(JT

A

G

)

JTAG_TDI

JTAG_TDO

Buffer

JP18

Summary of Contents for Prospector P1100



























































































































































Reviews:

No comments