ARM Cortex-R4 Technical Reference Manual Download Page 86

Page: 86 / 436

System Control

ARM DDI 0363G

4-16

ID073015

Non-Confidential

Table 4-4

shows the CTR bit assignments.

To access the CTR, read CP15 with:

MRC p15, 0, <Rd>, c0, c0, 1 ; Read CTR

4.3.4

c0, TCM Type Register

The TCMTR characteristics are:

Purpose

Informs the processor of the number of ATCMs and BTCMs in the system

Usage constraints

The TCMTR is:
•

a read-only register

•

accessible in Privileged mode only.

Configurations

Available in all processor configurations.

Attributes

See

Table 4-5 on page 4-17

Figure 4-9

shows the TCMTR bit assignments.

Figure 4-9 TCMTR Register bit assignments

Table 4-4 CTR Register bit assignments

Bits Name

Function

[31:28]

Always b1000.

[27:24]

CWG Cache

Write-back Granule:

0x0

= no information provided. See maximum cache line size in

c0, Current Cache Size

Identification Register

on page 4-34

[23:20]

ERG

Exclusives Reservation Granule:

0x0

= no information provided.

[19:16]

DMinLine

Indicates log2 of the number of words in the smallest cache line of the data and unified caches
controlled by the processor:

0x3

= eight words in an L1 data cache line.

[15:14]

Always

0x3

[13: 4]

Always

0x000

[3: 0]

IMinLine

Indicates log2 of the number of words in the smallest cache line of the instruction caches
controlled by the processor:

0x3

= eight words in an L1 instruction cache line.

31 30 29 28

19 18

16 15

3 2

0 0

Reserved

BTCM

Reserved

ATCM

Summary of Contents for Cortex-R4


















































































































































































































































































































































































































































Search results

Summary of Contents for Cortex-R4

Reviews:

Related manuals for Cortex-R4

Brands by name

Popular brands

ARM Cortex-R4, Technical Reference Manual

Search results

Summary of Contents for Cortex-R4

Reviews:

Related manuals for Cortex-R4

Brands by name

Popular brands