ARM Cortex-R4 Technical Reference Manual Download

Page: 72 / 436

System Control

ARM DDI 0363G

4-2

ID073015

Non-Confidential

4.1

About system control

This section gives an overview of the system control coprocessor. It contains the following
sections:
•

System identification control and configuration

•

MPU control and configuration

on page 4-3

•

Cache control and configuration

on page 4-3

•

Interface control and configuration

on page 4-4

•

System performance monitor

on page 4-4

•

System validation

on page 4-5

The purpose of the system control coprocessor, CP15, is to control and provide status
information for the functions implemented in the processor.

The system control coprocessor does not exist in a distinct physical block of logic.

4.1.1

System identification control and configuration

The system identification control and configuration registers provide overall management of:
•

memory functionality

•

interrupt behavior

•

exception handling

•

program flow prediction

•

coprocessor access rights for CP0-CP13, including the VFP, CP10-11.

The system identification control and configuration registers also provide the processor ID and
information on configured options.

The system identification control and configuration registers consist of 18 read-only registers
and seven read/write registers.

Figure 4-1

shows the arrangement of registers in this functional

group.

Figure 4-1 System control and configuration registers

Some of the functionality depends on how you set external signals at reset.

CRn

Coprocessor Access Register

Auxiliary Control Register

System Control Register

c13

Context ID Register

Opcode_2

CRm

Opcode_1

Main ID Register

Debug Feature Register 0

Auxiliary Feature Register 0

{0, 1}

Processor Feature Registers 0, 1

Multiprocessor ID Affinity Register

Memory Model Feature Registers 0 - 3

Instruction Set Attributes Registers 0 - 5

{4–7}

{0-5}

Write-only

Accessible in User mode

Read-only

Read/write

FCSE PID Register

c15

Secondary Auxiliary Control Register

Build Options Register 1

Build Options Register 2

Summary of Contents for Cortex-R4


















































































































































































































































































































































































































































Search results

Summary of Contents for Cortex-R4

Reviews:

Related manuals for Cortex-R4

Brands by name

Popular brands

ARM Cortex-R4, Technical Reference Manual

Search results

Summary of Contents for Cortex-R4

Reviews:

Related manuals for Cortex-R4

Brands by name

Popular brands