ARM Cortex-R4 Technical Reference Manual Download | Manualshive

Page: 36 / 436

background image

Functional Description

ARM DDI 0363G

Copyright © 2006-2011 ARM Limited. All rights reserved.

2-11

ID073015

Non-Confidential

2.3

Clocking and resets

Before you can run application software on the processor, it must be reset and initialized,
including loading the appropriate software-configuration. This section describes the signals for
clocking and resetting the processor. It contains the following sections:
•

•

•

.

See

Initialization

for information on software initialization.

2.3.1

Resets

The processor has the following reset inputs:

nRESET

This signal is the main processor reset that initializes the majority of the
processor logic.

PRESETDBGn

This signal resets processor debug logic.

nSYSPORESET

This signal is the reset that initializes the entire processor and all its
interfaces, including CP14 debug logic and the APB debug logic. See
CP14 registers reset on page 11-23 for information.

nCPUHALT

This signal stops the processor from fetching instructions after reset.

All of these are active-LOW signals that reset logic in the processor. You must take care when
designing the logic to drive these reset signals.

The processor synchronizes the resets to the relevant clock domains internally.

2.3.2

Reset modes

The reset signals in the processor enable you to reset different parts of the design independently.

shows the reset signals, and the combinations and possible applications that you can

use them in.

All reset signals are synchronized within the processor. You do not have to synchronize either
edge of any of the reset signals. Unless otherwise stated, whenever

nRESET

is asserted, it must

be held asserted for at least four

CLKIN

cycles to ensure correct reset operation.

Table 2-1 Reset modes

Reset mode

nRESET

PRESETDBGn

nSYSPORESET

nCPUHALT

Application

Power-on reset

0

x

0

x

Reset at power up, full system
reset. Hard reset or cold reset.

Processor reset

0

x

1

x

Reset of processor only,
watchdog reset. Soft reset or
warm reset.

Normal

1

x

1

1

Normal run mode.

Halt

1

x

1

0

Halting debug-mode,
provided normal mode has
not been entered since reset.

Debug reset

x

0

x

x

Resets all debug logic and the
debug APB interface.

«
...
34
35
36
37
38
...
»

Summary of Contents for Cortex-R4





















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cortex-R4

DS1-MP10RX series

Brand: NEC Pages: 39

Brand: Panasonic Pages: 16

Brand: Scarlett Pages: 23

Brand: TZS First AUSTRIA Pages: 14

Brand: Bear Pages: 16

Brand: FeelTech Pages: 7

Spacemaker CG800C

Brand: Black & Decker Pages: 21

Spacemaker CG700

Brand: Black & Decker Pages: 23

Brand: Black & Decker Pages: 20

Brand: Black & Decker Pages: 20

Brand: Electrolux Pages: 4

Brand: OBH Nordica Pages: 24

AstroFinder 506

Brand: Meade Pages: 1

Brand: Panamorph Pages: 16

Brand: JBL Pages: 68

Bravetti FP105B

Brand: Euro-Pro Pages: 10

ELPMBP03 - Structural Round Ceiling Plate

Brand: Epson Pages: 7

Brand: Vivo Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands