ARM Cortex-R4 Technical Reference Manual Download Page 226 | Manualshive

Page: 226 / 436

background image

Level Two Interface

ARM DDI 0363G

Copyright © 2006-2011 ARM Limited. All rights reserved.

9-3

ID073015

Non-Confidential

9.2

AXI master interface

The processor has a single AXI master interface, with one port that is used for:
•

Icache linefills

•

Dcache linefills and evictions

•

Non-cacheable

(NC) Normal-type memory instruction fetches

•

NC Normal-type memory data accesses

•

Device and Strongly-ordered type data accesses, normally to peripherals.

The port is 64 bits wide, and conforms to the AXI standard as described in the

AMBA AXI

Protocol Specification

. Within the AXI standard, the master port uses the

AWUSERM

and

ARUSERM

signals to indicate inner memory attributes.

The master interface can run at the same frequency as the processor or at a lower synchronous
frequency. See

AMBA interface clocking

for more information.

In addition, the AXI master interface produces or checks parity bits for each AXI channel. These
additional signals are not part of the AXI specification.

Note

In this section,

AXI slave

describes the AXI slave in the external system that is connected to the

Cortex-R4 AXI master port. This might not be the Cortex-R4 AXI slave port.

The following sections describe the attributes of the AXI master interface, and provide
information about the types of burst generated:
•

Identifiers for AXI bus accesses

•

Write response

•

Linefill buffers and the AXI master interface

•

Eviction buffer

•

Memory attributes

shows the AXI master interface attributes.

Table 9-1 AXI master interface attributes

Attribute

Value

Comments

Write issuing capability

4

Made up of four outstanding writes that can be evictions, single writes, or write
bursts.

a

Read issuing capability

7

Made up of five linefills on the data side, one NC read on the data side, and one
read on the instruction side, that can be NC or linefill.

Combined issuing capability

-

Write ID capability

2

-

Write interleave capability

1

The AXI master interface presents all write data in order.

Read ID capability

7

Made up of five linefills on the data side, one NC read on the data side, and one
linefill or NC read on the instruction side.

a. When there are three outstanding write transactions, only data is issued for the fourth. Only three outstanding write addresses

are issued.

«
...
224
225
226
227
228
...
»

Summary of Contents for Cortex-R4





















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cortex-R4

Brand: Breville Pages: 7

Brand: VEVOR Pages: 8

Brand: ELECRAFT Pages: 31

Brand: Coline Pages: 24

Brand: Hyundai Pages: 60

K 711 Chopex Maxi

Brand: KING Pages: 12

Brand: Applica Pages: 2

Brand: TERMOZETTA Pages: 40

Brand: HELIX Pages: 28

Brand: at professional Pages: 20

Cable Lock Kit LC-1

Brand: CHIEF Pages: 1

Brand: Panamorph Pages: 16

Brand: Hamilton Beach Pages: 11

Brand: Vdwall Pages: 20

Brand: Gastroback Pages: 36

Brand: Kenwood Pages: 63

Brand: Kenwood Pages: 164

Brand: Kenwood Pages: 122

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands