ARM Cortex-M4 Generic User Manual Download Page 49

Page: 49 / 276

The Cortex-M4 Instruction Set

ARM DUI 0553A

3-2

ID121610

Non-Confidential

3.1

Instruction set summary

The processor implements a version of the Thumb instruction set.

Table 3-1

lists the supported

instructions.

Note

Table 3-1

•

angle brackets, <>, enclose alternative forms of the operand

•

braces, {}, enclose optional operands

•

the Operands column is not exhaustive

•

Op2

is a flexible second operand that can be either a register or a constant

•

most instructions can use an optional condition code suffix.

For more information on the instructions and operands, see the instruction descriptions.

Table 3-1 Cortex-M4 instructions

Mnemonic

Operands

Brief description

Flags

Page

ADC, ADCS

{Rd,}

Rn,

Op2

Add with Carry

N,Z,C,V

page 3-41

ADD, ADDS

{Rd,}

Rn, Op2

Add

N,Z,C,V

page 3-41

ADD, ADDW

{Rd,}

Rn, #imm12

Add

page 3-41

ADR

Rd, label

Load PC-relative Address

page 3-23

AND, ANDS

{Rd,} Rn, Op2

Logical AND

N,Z,C

page 3-44

ASR, ASRS

Rd, Rm, <Rs|#n>

Arithmetic Shift Right

N,Z,C

page 3-46

label

Branch

page 3-119

BFC

Rd, #lsb, #width

Bit Field Clear

page 3-115

BFI

Rd, Rn, #lsb, #width

Bit Field Insert

page 3-115

BIC, BICS

{Rd,}

Rn, Op2

Bit Clear

N,Z,C

page 3-44

BKPT

#imm

Breakpoint

page 3-158

label

Branch with Link

page 3-119

BLX

Branch indirect with Link

page 3-119

Branch indirect

page 3-119

CBNZ

Rn, label

Compare and Branch if Non Zero

page 3-121

CBZ

Rn, label

Compare and Branch if Zero

page 3-121

CLREX

Clear Exclusive

page 3-38

CLZ

Rd, Rm

Count Leading Zeros

page 3-48

CMN

Rn, Op2

Compare Negative

N,Z,C,V

page 3-49

CMP

Rn, Op2

Compare

N,Z,C,V

page 3-49

CPSID

Change Processor State, Disable Interrupts

page 3-159

CPSIE

Change Processor State, Enable Interrupts

page 3-159

Summary of Contents for Cortex-M4



















































































































































































































































































Search results

Summary of Contents for Cortex-M4

Reviews:

Brands by name

Popular brands

ARM Cortex-M4, Generic User Manual

Search results

Summary of Contents for Cortex-M4

Reviews:

Brands by name

Popular brands