ARM Cortex-M4 Page 152 Generic User Manual Download

Page: 152 / 276

The Cortex-M4 Instruction Set

ARM DUI 0553A

3-105

ID121610

Non-Confidential

3.7.7

UQADD and UQSUB

Saturating Add and Saturating Subtract Unsigned.

Syntax

op{

cond

} {

op{

cond

} {

where:

Is one of:

UQADD8

Saturating four unsigned 8-bit integer additions.

UQADD16

Saturating two unsigned 16-bit integer additions.

UDSUB8

Saturating four unsigned 8-bit integer subtractions.

UQSUB16

Saturating two unsigned 16-bit integer subtractions.

cond

Is an optional condition code, see

Conditional execution

on page 3-18

Specifies the destination register.

Rn, Rm

Are registers holding the first and second operands.

Operation

These instructions add or subtract two or four values and then writes an unsigned saturated value
in the destination register.

The

UQADD16

instruction:

•

Adds the respective top and bottom halfwords of the first and second operands.

•

Saturates the result of the additions for each halfword in the destination register to the
unsigned range 0

≤

−

1, where

is 16.

The

UQADD8

instruction:

•

Adds each respective byte of the first and second operands.

•

Saturates the result of the addition for each byte in the destination register to the unsigned
range 0

≤

−

1, where

is 8.

The

UQSUB16

instruction:

•

Subtracts both halfwords of the second operand from the respective halfwords of the first
operand.

•

Saturates the result of the differences in the destination register to the unsigned range
0

≤

−

1, where

is 16.

The

UQSUB8

instructions:

•

Subtracts the respective bytes of the second operand from the respective bytes of the first
operand.

•

Saturates the results of the differences for each byte in the destination register to the
unsigned range 0

≤

−

1, where

is 8.

Restrictions

Do not use SP and do not use PC

Summary of Contents for Cortex-M4



















































































































































































































































































Search results

Summary of Contents for Cortex-M4

Reviews:

Related manuals for Cortex-M4

Brands by name

Popular brands

ARM Cortex-M4, Generic User Manual

Search results

Summary of Contents for Cortex-M4

Reviews:

Related manuals for Cortex-M4

Brands by name

Popular brands