ARM Cortex A9 Technical Reference Manual Download Page 188

Page: 188 / 213

Signal Descriptions

ARM DDI 0388I

A-19

ID073015

Non-Confidential

A.11

MBIST interface

Table A-21

shows the MBIST interface signals. These signals are present only when the BIST

interface is present.

The size of some MBIST signals depends on whether the implementation has parity support or
not.

Table A-22

shows these signals with parity support implemented.

Table A-23

shows these signals without parity support implemented.

See the

Cortex-A9 MBIST TRM

for a description of MBIST.

Table A-21 MBIST interface signals

Name

I/O

Source

Description

MBISTADDR[10:0]

MBIST controller

MBIST address bus

MBISTARRAY[19:0]

MBIST arrays used for testing RAMs

MBISTENABLE

MBIST test enable

MBISTWRITEEN

Global write enable

MBISTREADEN

Global read enable

Table A-22 MBIST signals with parity support implemented

Name

I/O

Source or destination

Description

MBISTBE[32:0]

MBIST controller

MBIST write enable

MBISTINDATA[71:0]

MBIST data in

MBISTOUTDATA[71:0]

MBIST data out

Table A-23 MBIST signals without parity support implemented

Name

I/O

Source/Destination

Description

MBISTBE[25:0]

MBIST controller

MBIST write enable

MBISTINDATA[63:0]

MBIST data in

MBISTOUTDATA[63:0]

MBIST data out

Summary of Contents for Cortex A9





















































































































































































































Search results

Summary of Contents for Cortex A9

Reviews:

Related manuals for Cortex A9

Brands by name

Popular brands

ARM Cortex A9, Technical Reference Manual

Search results

Summary of Contents for Cortex A9

Reviews:

Related manuals for Cortex A9

Brands by name

Popular brands