ARM Cortex-A9 MBIST Technical Reference Manual Download Page 26

Page: 26 / 72

Functional Description

2-2

ARM DDI 0414C

Non-Confidential

Restricted Access

2.1

Functional overview

This section describes the interface between the MBIST controller and the RAMs that
the MBIST controller tests:

•

MBIST controller interface

•

MBISTINDATA and MBISTOUTDATA mapping

on page 2-4

•

MBIST controller implementation

on page 2-10.

2.1.1

MBIST controller interface

The MBIST controller has one MBIST port, see Appendix A

Signal Descriptions

. Only

one set of RAM is accessed by the MBIST controller at any time.

You can use the MBIST controller for testing the Cortex-A9 processor compiled RAMs.
You can also choose to design your own MBIST controller.

For the MBIST to run correctly on the Cortex-A9 processor if the dormant/power off
wrappers are implemented, you have to set the signals on the Cortex-A9 processor
interface as shown in Table 2-1:

Table 2-2 shows the interfaces between the MBIST controller and the RAMs that
MBIST tests.

Table 2-1 Cortex-A9 signal settings for MBIST

Signal name

Setting

CPURAMCLAMP[3:0]

4’b0000

CPUCLAMP[3:0]

4’b0000

RVALIDM1

1'b0

SCURAMCLAMP

1’b0

Table 2-2 RAM arrays and MBIST controller interfaces

RAM Name

MBISTARRAY
bit

MBISTINDATA
bits

MBISTBE
bits

MBISTOUTDATA
bits

Max
address
bits

SCU tag RAM way 3

[19]

[22:0]

[54:32]

[8:0]

SCU tag RAM way 2

[19]

[22:0]

[8:0]

SCU tag RAM way 1

[18]

[22:0]

[54:32]

[8:0]

Summary of Contents for Cortex-A9 MBIST

































































Search results

Summary of Contents for Cortex-A9 MBIST

Reviews:

ARM Cortex-A9 MBIST, Technical Reference Manual, Page: 26 / 72

Search results

Summary of Contents for Cortex-A9 MBIST

Reviews: