ARM ARM9TDMI Technical Reference Manual Download | Manualshive

Page: 60 / 154

background image

Debug Support

5-6

Copyright © 1998, 1999 ARM Limited. All rights reserved.

ARM DDI0145B

Figure 5-2 Breakpoint timing

5.3.2

Breakpoints and exceptions

A breakpointed instruction may have a prefetch abort associated with it. If so, the
prefetch abort takes priority and the breakpoint is ignored. (If there is a prefetch abort,
instruction data may be invalid, the breakpoint may have been data-dependent, and as
the data may be incorrect, the breakpoint may have been triggered incorrectly.)

SWI and undefined instructions are treated in the same way as any other instruction
which may have a breakpoint set on it. Therefore, the breakpoint takes priority over the
SWI or undefined instruction.

On an instruction boundary, if there is a breakpointed instruction and an interrupt (

IRQ

or

FIQ

), the interrupt is taken and the breakpointed instruction is discarded. Once the

interrupt has been serviced, the execution flow is returned to the original program.

ǽřŗǱŖǾ

ǽřŗǱŖǾ

'GHEXJ

(GHEXJ

(GHEXJ

)

'

(

0

:

)

'

(

0

:

),

',

(,

0,

:,

Z

Z

Z,

,

«
...
58
59
60
61
62
...
»

Summary of Contents for ARM9TDMI



























































































































































Reviews:

No comments

Related manuals for ARM9TDMI

RocketLink-G 3088/I

Brand: Patton electronics Pages: 61

DataPlot CB1224

Brand: B-G Instruments Pages: 4

Brand: DigiTech Pages: 6

Brand: Vega Pages: 12

Brand: ZiLOG Pages: 11

PXI PXITM -1000

Brand: National Instruments Pages: 55

iMarc SLV 9820-2M

Brand: Paradyne Pages: 24

Brand: ICP Pages: 142

Bolide BN-NVR/NX

Brand: GSA Pages: 101

Brand: Commell Pages: 18

Brand: ICP DAS USA Pages: 62

CU8210-D001-0200

Brand: Beckhoff Pages: 25

Brand: HYCON Pages: 13

EK-Quantum Vector FE RTX 3080

Brand: ekwb Pages: 20

Brand: Vecow Pages: 52

Brand: Laird Pages: 8

VOD-W Server VBrick v4.2.3

Brand: VBrick Systems Pages: 92

Brand: Optoma Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands