ARM ARM9TDMI Technical Reference Manual Download | Manualshive

Page: 146 / 154

background image

ARM9TDMI Signal Descriptions

A-8

Copyright © 1998, 1999 ARM Limited. All rights reserved.

ARM DDI0145B

A.5

Debug signals

Table A-5 Debug signals

Name

Direction

Description

COMMRX

Output

Communications Channel Receive. When HIGH, this signal denotes that the comms
channel receive buffer contains data waiting to be read by the ARM9TDMI.

COMMTX

Output

Communications Channel Transmit. When HIGH, this signal denotes that the comms
channel transmit buffer is empty and the ARM9TDMI can write new data to the comms
channel.

DBGACK

Output

Debug Acknowledge. When HIGH, this signal indicates the ARM9TDMI is in debug
state.

DBGEN

Input

Debug Enable. This input signal allows the debug features of the ARM9TDMI to be
disabled. This signal should be LOW only when debugging will not be required.

DBGRQI

Output

Internal Debug Request. This signal represents the debug request signal which is
presented to the processor core. This is a combination of

EDBGRQ

, as presented to the

ARM9TDMI, and bit 1 of the debug control register.

DEWPT

Input

Data Watchpoint. This is an input which allows external hardware to halt execution of
the processor for debug purposes. If HIGH at the end of phase 1 following a data memory
request cycle, it will cause the ARM9TDMI to enter debug state.

EDBGRQ

Input

External Debug Request. When driven HIGH, this causes the processor to enter debug
state after execution of the current instruction completes.

EXTERN0

Input

External Input 0. This is an input to watchpoint unit 0 of the EmbeddedICE macrocell in
the processor which allows breakpoints/watchpoints to be dependent on an external
condition.

EXTERN1

Input

External Input 1. This is an input to watchpoint unit 1 of the EmbeddedICE macrocell in
the processor which allows breakpoints/watchpoints to be dependent on an external
condition.

IEBKPT

Input

Instruction Breakpoint. This is an input which allows a external hardware to halt the
execution of the processor for debug purposes. If HIGH at the end of phase 1 following
an instruction memory request cycle, it causes the ARM9TDMI to enter debug state if
the relevant instruction reaches the execute stage of the processor pipeline.

INSTREXEC

Output

Instruction Executed. Indicates that in the previous cycle the instruction in the execute
stage of the pipeline passed its condition codes, and was executed.

«
...
144
145
146
147
148
...
»

Summary of Contents for ARM9TDMI



























































































































































Reviews:

No comments

Related manuals for ARM9TDMI

Brand: F5 Pages: 72

Active Module Carrier VX402C-64

Brand: C&H Pages: 32

Brand: Compal Pages: 47

Brand: Renesas Pages: 4

Brand: AMC Pages: 28

Brand: Beckhoff Pages: 84

Brand: Netequalizer Pages: 14

Brand: Abus Pages: 98

Brand: Commell Pages: 17

Brand: Paradyne Pages: 216

Brand: Jatontec Pages: 13

Brand: Advantage Pages: 4

Brand: Advantech Pages: 114

Brand: RadioLAN Pages: 24

Brand: Huawei Pages: 15

Brand: Huawei Pages: 20

ViewPoint 8650 V100R008

Brand: Huawei Pages: 36

Brand: Huawei Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands