useR mANuAl
The tower fan must always be used with the base assembled and in
upright position. Attach the base to the main body in the order given below.
i.
Remove the sub assemblies from the box.
ii.
Remove the remote control handset and supply cord/plug from the
plastic bag.
iii.
Unscrew the 2 wing screws from the bottom of the main body.
iv.
Assemble the 2 halves of the base plate with the supply cord of the
main unit passing through the central aperture. Fix the base plate
halves firmly together by sliding the locating posts on one side into
their mating holes on the other side.
v.
Fit the assembled base plate over the bottom of the main
body then fasten the 2 wing screws to hold the base
securely to the main body.
vi.
Clip the supply cord under the 2 locating clips on the
underside of the base ensuring that it passes through the
semi-circular opening on in the outer rim of the base.
Make sure that you read all of the safety warnings before you
operate this unit for the first time. Plug the unit to a standard mains
socket and turn on the mains switch. The unit will beep twice.
oN / speed button
low
medium
high
i.
Press the ON/ Speed button to start the unit.
ii.
The unit will start operating on the settings and speed
selected when the fan was last turned off.
iii.
Press the button repeatedly to change the fan speed from Low
to Medium to High and the speed indicator will change on the
display panel.
off button
i.
Press this button once to turn the unit off.
mode button
Change the mode to the desired type (Normal, Natural and Sleep)
by pressing the mode button repeatedly. There are three settings for
oscillation and the graphic display will display the selected type of
oscillation.
Normal mode
When the unit is turned ON it will operate in Normal mode which is
the default mode of the unit – see graphic above. Under this mode the
fan speed remains constant at the set speed (Low / Medium/ High).
Corresponding speed indicator will glow on the display panel. This
mode is recommended for normal operation.
Assembly
opeRATIoN
opeRATIoN
coNTRol pANel & RemoTe coNTRol
1
3
2
control panel
led display
main fan
body
carry handle
Vent outlet
support base
112cm
Tower Fan
with Remote Control
supply cord
Wing screws
locating
posts
mating
holes
fan base
fan base
central
Aperture
fan body
fan body
A.
On/Speed
b.
Off
c.
Mode
d.
Swing Key
e.
Timer
c
d
c
e
b
A
A e
d
b
Natural mode
i.
Press the mode button until the graphic display comes up with which shows that the natural
mode is selected. In this mode the fan will operate in a preset program which varies the speed
of the fan between low, medium, high & off, giving a natural breeze effect.
ii.
Each speed setting has its own preset program which will vary the speed of the fan accordingly.
If the fan speed is set at High the fan will operate in high natural model which varies the speed
between high, medium, low & off.
If the fan speed is set at medium the fan will operate in medium natural mode which varies the
fan speed between medium, low & off.
If the fan speed is set at low the fan will operate in low natural mode which varies the fan speed
between low, medium & off.
sleep mode
i.
Press the mode button until the sleep mode graphic above appears in the LED panel.
Under this mode the fan speed switches between set speeds thus saving energy during night.
ii.
If the fan is set at high speed the fan will operate in high, medium and low natural mode for
approximately half an hour at each speed setting. This cycle will continue until the preset time is
reached or the unit is turned off.
If the fan is set at medium speed the fan will operate in medium and low natural mode for
approximately half an hour at each speed setting. This cycle will continue until the preset time is
reached or the unit is turned off.
If the fan is set at low speed setting the fan will continue to operate in low natural mode setting
until the preset time is reached or the unit is turned off.
Timer button
i.
Press the timer button repeatedly to obtain the desired operating time (1 Hour to 8.0 Hours).
Each time the button is pressed the time interval is incremented upward. The corresponding
display panel will show. 1H–2H–4H–8H then off. The unit will shut off automatically when the
set time has been reached.
swing button
i.
Pressing the swing button selects 80° angle of continuous horizontal oscillation of
the main unit.
i.
The remote control handset requires a single CR2032 (or equivalent) 3V battery.
ii.
To install the battery remove the battery tray as shown on the rear of the handset.
iii.
Insert the battery as per the polarity shown.
iv.
The remote control has the same functions as the buttons on the
control panel keypad.
v.
To use the remote control make sure that the fan is plugged into
the mains supply, then point the handset to the sensor located
beneath the keypad (within the display panel) and press the
desired button. The remote control operating range is up to
6 metres. Make sure that there is no obstacle between the
remote and the sensor.
Note: The unit incorporates an infra red sensor. ensure that
the handset is directed toward the sensor (within the display
panel), otherwise the remote control will not function.
RemoTe coNTRol
4
CPIN002690/3
THe
MeTroPoLIS
locating
clips