Arlec guarantees this product in accordance with the Australian Consumer Law.
Arlec also warrants to the original first purchaser of this product (“you”) from a retailer that this
product will be free of defects in materials and workmanship for a period of 12 months from the date
of purchase; provided the product is not used other than for the purpose, or in a manner not within
the scope of the recommendations and limitations, specified by Arlec, is new and not damaged at
the time of purchase, has not been subjected to abuse, misuse, neglect or damage, has not been
modified or repaired without the approval of Arlec and has not been used for commercial purposes
(“Warranty”).
If you wish to claim on the Warranty, you must, at your own expense, return the product, and provide
proof of original purchase and your name, address and telephone number, to Arlec at the address
below or the retailer from whom you originally purchased the product within 12 months from the date
of purchase.
Arlec will (or authorise the retailer to) assess any claim you may make on the Warranty in the above
manner and if, in Arlec’s reasonable opinion, the Warranty applies, Arlec will at its own option and
expense (or authorise the retailer to) replace the product with the same or similar product or repair
the product and return it to you or refund the price you paid for the product. Arlec will bear its own
expenses of doing those things, and you must bear any other expenses of claiming on the Warranty.
The Warranty is in addition to other rights and remedies you may have under a law in relation to the
product to which the Warranty relates.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced
if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Arlec Australia Pty. Ltd. ACN 009 322 105 (“Arlec”) gives the Warranty.
Arlec’s telephone number, address and email address are:
Customer Service: (03) 9982 5111
Building 3, 31 – 41 Joseph Street, Blackburn North, Victoria, 3130
Blackburn North LPO, P.O. Box 1065, Blackburn North, 3130
Email: [email protected]
wARRANTY
4
CPIN002354
5
6
NOTE: It is advisable to use a separate
independent wall switch to ensure the simplest
operation of this unit.
In normal operation when first switched on,
the unit will operate only in automatic mode.
The unit will not operate the lamp in daylight.
When dark, the light will be activated by
movement across the detection area.
• To switch off completely, switch the wall
switch to OFF.
This Sensor light has a built-in photoelectric cell
that automatically senses daylight and keeps
the light off during daylight hours.
NOTE:
1. This highly responsive unit may occasionally
activate due to rapid environment changes.
2. To avoid false triggering do not install this unit
near wiring of large appliances such as
air conditioners, refrigerators, fluorescent
lights etc.
3. When first switching on allow approximately
30 seconds warm up time for sensor
operation to settle to normal sensitivity.
During daylight hours, the unit can be ‘walk’
tested by turning the daylight level (“LUX”) control
fully clockwise. Test by switching the unit on and
walk slowly across the detection area.
Check that the light will remain on for a period
set by adjusting the timer, from approx 10 seconds
to 3 minutes depending on the setting after
the last movement in the sensing area occurs.
(Refer to adjusting the daylight level and
time delay)
First, switch off the mains power to the unit. If
unit has been operating, allow it to cool before
handling. Open the lamp by unscrewing the
fasteners on the front trim and diffuser, then
remove the diffuser and remove/replace bulb,
(use only 240 volt a.c. ES bulb 60 watt max),
refit diffuser. Compact fluorescent bulbs may be
fitted in this light.
For normal operation, the daylight level (“LUX”)
control is set to fully anti-clockwise. For walk
testing in daylight the LUX control is set fully
clockwise.
If you find in normal operation that you would
like the light to come on sooner, adjust slightly
back from the full anti-clockwise position. See
figure 5 below. To adjust the time delay turn the
time adjusting arrow clockwise to increase the
delay and anti-clockwise to decrease the
delay. The time delay is from approximately
10 seconds to 3 minutes. It is recommended
to use shorter time delays.
Detection Range :
8 metres at 120° scan
approx.
Time On (fixed) :
10 s to 3 min approx.
Detection Circuitry : Passive controlled
infrared motion sensor.
Ambient Light
<10 Lux adjustable
required to operate
to daylight
in Auto Mode:
Maximum Globe :
ES 60 watt max globe
Weatherproof Rating : IP44
OpERATION
TROuBLE SHOOTING GuIDE
TO TEST
SpECIfICATIONS
mAINTENANCE
GLOBE REpLACEmENT
DAYLIGHT SENSOR
(pHOTOELECTRIC CELL)
ADjuSTING DAYLIGHT
LEvEL AND TImE DELAY
Note: Passive infra-red detectors are more sensitive in cold weather than warm weather.
pROBLEm
pOSSIBLE CAuSE
SuGGESTED REmEDY
Light does not switch ON when there
is movement in the detection area.
1. No mains voltage.
Check all connections, and fuses/switches.
2. Globe faulty or missing.
Check. Replace.
3. Wiring incorrect.
Re-check.
4. Nearby lighting is too bright.
Redirect other lights or relocate unit.
Light switches ON for
no apparent reason.
1. Heat sources such as aircon. vents,
heater flues, barbecues or very cold
objects are near sensor.
Remove these sources if possible.
2. Animals/birds e.g. possums or
domestic animals.
Nil
3. Interference from on/off switching of
electric fans or lights on the same
circuit as your Sensor Light.
(This problem does not always occur
but a faulty switch or noisy fluorescent
light may cause the Sensor Light to
switch on.)
Should the false triggering become
troublesome, consider:
(A) Replacing a faulty switch.
(B) Replacing noisy fluorescent tubes
and/or starters.
(C) Connecting the Sensor Light to a
separate circuit. (In most cases where
one or more of the above suggestions
have been carried out, false triggering
has been reduced.)
4. Voltage surges
Nil
5. Radio frequency transmissions from
mobile phones, CB’s etc.
Nil
6. On during daytime.
Check daylight level (“LUX”) control is
fully anti-clockwise.
Light remains ON .
1. Wiring is incorrect.
Recheck wiring.
2. Time delay set too long.
Turn time control anti-clockwise
To avoid dust build up and ensure proper functioning of the Sensor Light, wipe the sensor lens lightly
with a damp cloth every 3 months.
Care should be taken when cleaning to prevent scratching. A soft cloth or fine-hair brush should be
used together with a nonabrasive cleaner. Do not use solvents or abrasive cleaners on any part of
your Sensor Light.
Figure 5.
CPIN002354