ARKSCAN ES321 User Manual Download Page 148

Page: 148 / 348

Enter 132 End

*/$%ENTR* *ZEND*

Setting up your Operation Modes

Procedure

(1)

Scan

Enter

barcode.

(2)

Scan

PreambleChar

barcode to configure Preamble Code.

(3)

Please refer to ASCII Code Table and Decimal/Hexadecimal Table in the appendix

to scan hexadecimal value barcodes representing the desired string which has to be

at most 2 characters in length

For instance, to set preamble code to be

<CR><LF>, scan

0, D, 0,

and then

to assign the specified hexadecimal value

“0D0A”.

(4)

Scan

SET

barcode to complete the variable-binding operation.

(5)

Scan

End

barcode to complete the configuration.

7-2-3-20.

Set Postamble Code

In the process of transmitting data, Postamble Code is appended to both the suffix code

and barcode data as a user-defined string to format the output data. However, Postamble

Code not simply works like Suffix Code to better format the transmitted messages, but, to

precisely describe it, expects to emulate line terminators to break transmission line.

Consequently, it is strongly suggested to associate this configurable parameter with

equivalent ASCII code value for line terminators. Please follow the below steps to

configure Postamble Code.

Procedure

(1)

Scan

Enter

barcode.

(2)

Scan

PostambleChar

barcode to configure Postamble Code.

(3)

Please refer to ASCII Code Table and Decimal/Hexadecimal Table in the

appendix to scan hexadecimal value barcodes representing the desired string

which has to be at most 2 characters in length. For instance, to set postamble

code to be <CR><LF>, scan

0, D, 0,

and then

to assign the specified

hexadecimal value “0D0A”.

(4)

Scan

SET

barcode to complete the variable-binding operation.

(5)

Scan

End

barcode to complete the configuration.

*BAEE3*

PostambleChar

BAEE3

(Length: 2 digits)

Summary of Contents for ES321





























































































































































































































































































































































Search results

Summary of Contents for ES321

Reviews:

ARKSCAN ES321, User Manual, Page: 148 / 348

Search results

Summary of Contents for ES321

Reviews: