Arkray GLUCOCARD 01-mini User Instruction Manual Download Page 67

Page: 67 / 76

Your blood glucose level is less than 20 mg/dL or there

was not enough blood on test strip. Repeat test with

new test strip. Make sure you use enough blood to

fill the strip. If this message shows again, contact

your healthcare professional immediately!

Your blood glucose level is more than 600 mg/

dL. Repeat test with new test strip. If this message

shows again, contact your healthcare professional

immediately.

Battery power is too low for testing. Replace batteries

immediately. Results may not be accurate when

testing with low battery symbol on.

Thermometer symbol. The meter temperature is

outside acceptable range of 50˚F-104˚F (10˚C-40˚C).

Allow the meter and test strips to warm up or cool

down slowly (20 minutes) until the temperature

warning symbol goes away.

Summary of Contents for GLUCOCARD 01-mini













































































Search results

Summary of Contents for GLUCOCARD 01-mini

Reviews:

Related manuals for GLUCOCARD 01-mini

Brands by name

Popular brands

Arkray GLUCOCARD 01-mini, User Instruction Manual

Search results

Summary of Contents for GLUCOCARD 01-mini

Reviews:

Related manuals for GLUCOCARD 01-mini

Brands by name

Popular brands