4
Operating Instructions and Parts Manual
29
00 CFM 3 SPEED
EVAPORATIVE COOLER
2/17
AZ Air Coolers LLC
CONTACT US
KUULKUBE® 2 YEAR LIMITED WARRANTY
For 2 YEARS from the original purchase of this product, Arizona Air Coolers LLC (company) will warranty this item. If you find any
defect in material or workmanship, through normal usage, return it to the place of purchase or to Arizona Air Coolers LLC for repair or
replacement at our discretion. In order to obtain this service send your tool and proof of purchase, transportation pre-paid, to Arizona Air
Coolers LLC . We will not be responsible for lost or damaged goods during transportation, please insure your package. If our inspection
verifies the defect, we will either repair or replace the product at our election, or we may elect to refund the purchase price if we cannot
readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no
defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.
Arizona Air Coolers LLC does not provide warranty for products labeled other than KUULKUBE® or PRIMOCOOL and will not provide
any warranty for products subjected to abnormal use. Abnormal use includes, but is not limited to, abuse, accident, alteration, neglect, and
unauthorized or unreasonable use or repairs. This warranty does not cover,Media Pads ,Filters, batteries, or calibration. We recommend
that you maintain COOLER AND WATER QUALITY. Water Damage to Components due to scale buildup is not covered under this
warranty, Change tank water regularly and clean tank weekly of left behind dissolved solids .Arizona Air Coolers LLC ® reserves the right
to makes any changes in construction or design at any time without any obligation in incorporating such changes to tools or equipment
previously sold.
Arizona Air Coolers LLC ® makes every effort to assure that its products meet high quality and durability standards, and warrants to the
original purchaser that this product is free from defects in materials and workmanship for the period of 2 YEARS from the date of
purchase. This warranty does not apply to damage due directly or indirectly to misuse, abuse, negligence or accidents, repairs or
alterations outside our facilities, criminal activity, improper installation, normal wear and tear or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. This warranty gives you specific
legal rights, and you may also have other rights, which vary from state to state.
Don’t forget to register your new KUULKUBE® product at www.KUULKUBE.COM
1. With access panel removed, simply pull off the pad retainer disc from
the pad pin.
2. With disc removed, remove the pins from the pads and carefully
remove pads from the fixed side mounting frame. Then do the same
for the back panel or panels.
3. Pads are made with a 45/45 flute and can be installed either side to
the frame. Just make sure the distribution pad that is fixed to the top
of the new media pad is at the top. This allows water get onto the
top of the pad evenly. The installation of the pads is opposite of the
removal, install the pad, insert pins and install the retaining disc.
4. Reinstall the back panel and you are ready to use the cooler again.
PUMP MAINTENANCE AND REPLACEMENT.
NOTE:
Disconnect power supply before this procedure.
The submersible pump is mounted inside the tank to the bottom with a
retention bracket. While you are cleaning the cooler the pump may be
removed and the strainer cap on the bottom of pump can be cleaned of
debris. If pump has failed and needs replacing follow these steps:
1. Remove retaining screws.
2. Remove the switch control panel from the top of cooler, by inserting a
small screwdriver into the tap slots and pop loose.
3. The pump is connected to the control via the white plastic clip.
Disconnect the pump clip and feed the plastic clip through the control
box into the cooler.
4. There may be cable ties holding cable to the motor mounting bracket.
Remove the pump from cooler when cable is free.
5. Re-install the new pump in reverse. Being sure to reconnect the cable in
the twist ties and secure the cable in a manner of which it stays clear of
fan blade when cooler is running. Re-attach the pump clip in the control
box. Be sure not to pull any other wires loose from control switches when
you have panel loose.
6. Re-install the control panel into the cabinet making sure it is
seated.
FLOAT VALVE REPLACEMENT OR ADJUSTMENT
NOTE:
Disconnect power supply before this procedure.
The float valve is mounted to the left side of cooler if you are facing the
front grill. It is held in place by the retaining nut that is visible from the
outside. The rubber washer is between the nut and cabinet. The rear
panel will have to be removed to adjust the float (if the water level is too
high or too low) or remove and replace a float that has failed to shut of
water supply.
NOTE:
Be sure that the PSI of the supply water is within the 50 PSI spec.
Before determining the float has failed.
1. The float valve can be purchased where you purchased your cooler.
2. Remove any hose adapters attached to the float valve nipple.
3. Remove the rear panel assembly as instructed in Section 5
4. Remove the float valve retaining nut and rubber washer. And remove
float valve from cabinet.
5. Re-install the float valve in reverse. Set the valve adjustment to around
60 degrees for best results.
