background image

5 / EN

 

TECHNICAL CHARACTERISTICS

For the technical specifi cations, refer to the nameplate (the nameplate is located next to the water in-
take/outlet pipes).

TABLE 1 - PRODUCT INFORMATION

Product range

VLS EVO 

45

VLS EVO 

80

VLS EVO 

45 WiFi

VLS EVO 

80 WiFi

Weight when empty 

kg 

21

32

21

32

Weight when full 

kg 

66

112

66

112

Installation

Vertical

Vertical

Vertical

Vertical

Model

Refer to the nameplate

SMART

X

X

X

X

Q

elec

 kWh

6,79

7,125

6,79

7,125

Q

elec , week, smart

 kWh

25,467

27,141

25,467

27,141

Q

elec , week, 

 kWh

28,758

32,041

28,758

32,041

Load profi le

M

M

M

M

L

wa

 dB

15

η

wh

39,1%

39,0%

39,1%

39,0%

V40 L

77

115

77

115

Heat loss 

kWh/day

0,964

1,317

0,964

1,317

Heat up times [15-60°C] 

minutes

60

112

29

56

Maximum inlet pressure [rated pressure] 

bar

12

Maximum design pressure 

bar

6

Set operating pressure expansion valve 

bar

6

Pre-charge pressure of the expansion vessel 

bar

3,5

Set opening T&P relief valve 

bar

7

Capacity L

45

80

45

80

The power consumption data in the table and the other information given in the Product Data Sheet 
(Enclosure A to this manual) are defi ned in relation to EU Directives 812/2013 and 814/2013.
The products without the label and the data sheet for water heaters and solar devices, stipulated in 
regulation 812/2013, are not intended to be used in such assemblies.
The device is equipped with a smart function that allows you to adapt the consumption to the user pro-
fi les. If operated correctly, the device has a daily consumption of “Qelec (Q

elec, week, smart

/Q

elec, week

) less than 

that of an equivalent product with no smart function”.

This appliance is conforming with the international electrical safety standards IEC 60335-1 and IEC 
60335-2-21.
The CE marking of the appliances attests its conformity to the following EC Directives, of which it 
satisfi es the essential requisites:
-  LVD Low Voltage Directive: EN 60335-1, EN 60335-2-21, EN 60529, EN 62233, EN 50106.
- EMC Electro-Magnetic Compatibility: EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3.
- RoHS2 Risk of Hazardous Substances: EN 50581.
- ErP Energy related Products: EN 50440.

- EN 12897:2016

This product is in conformity with REACH regulations.

Summary of Contents for VELIS EVO

























Reviews: