Ofrecido por www.electromanuales.com
ARISTON DISHWASHER - Instructions for installation and use
15
D
ISHWASHER
First of all.
After performing all the operations
described in the previous
paragraphs, turn the water tap on
completely and press ON-OFF
button "
A
": you will hear a short
beep and indicator light "
B
" lights
up. Now the appliance is on and
ready to be programmed.
Selecting the wash
cycle.
Turn knob "
M
" until the reference
notch on the knob corresponds with
the number or symbol for the cycle
you wish to set (have a look at the
wash cycle table on page 17). After
a few seconds, you will hear a short
beep: the wash cycle has begun and
indicator "
G
" displays the symbol
corresponding to the cycle starting
phase.The counter "
L
" will indica-
te the estimated amount of time
left until the end of the wash cycle.
Do not expect a precise
countdown as the wash cycle
starts with an estimated cycle time
that is updated as the cycle
progresses and according to a
number of parameters that affect
the cycle itself (such as water
hardness, the temperature of the
water, the degree of soil, etc.).
The dishwasher informs
you.
Your dishwasher is provided with
an indicator light (
G
) with 4
symbols which come on as the
appliance carries out the wash
phase indicated by the indicator
light.
These indicator lights represent the
phases corresponding to:
pre-wash, wash, rinses, drying.
At all times, your dishwasher tells
you where it is at.
Modifying a wash cycle
in progress.
But if you have chosen the wrong
cycle, not to worry! You can modify
the wash cycle in progress only if it
has only just started. Turn the knob
until it reaches the
Reset
position
and, after a few seconds, you will
hear 4 beeps. At this point, indicator
"
G
" comes off and 3 dashes appear.
This indicates that all the settings
have been cancelled. You are now
free to re-set the correct wash
cycle.
You've left out a dish?
Well, it happens to everyone.
Interrupt the wash cycle by
pressing the ON-OFF button, insert
the dish you had forgotten and
press the ON-OFF button again.
The cycle will start up from where
you interrupted it.
Finished?
The end of the wash cycle is
signalled by a double beep, and a
flashing END comes up on the
display. Bring the selector back to
the Reset position,and the 3 dashes
for programming cancellation will
appear.
Turn off the water tap.
Wait a few minutes before unload-
ing the dishes: they are very hot! If
you wait a little while, they dry bet-
ter thanks to the steam.
Empty the lower rack first.
There's been a power
failure? Have you
opened the dishwasher
door?
The wash cycle stops and then
restarts when the electricity comes
back on or when you close the door.
Everything is under control!
You have loaded your dishes and you now have
to set the wash cycle. It takes just one minute
to learn how
Starting the dishwasher
Make sure the
wash cycle has
ended before
removing the
dishes!
You want to wash on
one rack only?
Remember to use half
the amount of detergent.
Your dishwasher also allows you
to wash half a load (choosing on
which rack), to save water and
electricity. Before setting any wash
cycle whatsoever, press button "
I
".
Each time the button is pressed,
you will hear a beep, and symbol
(upper rack) and symbol
(lower rack) appear on indicator
"
N
". Press it once more to reset the
rack selection and the dishwasher
will consequently wash on both
racks.
How to programme
extra drying
If you want your dishes to be
perfectly dry, follow the
instructions below.
Set the knob to RESET and make
any specific settings, such as:
-
upper or lower rack
-
delayed start
Start the wash cycle by turning
the knob: observe symbol for
drying: it will flash for about 4
seconds, while the word "OFF"
appears on the display (extra drying
disabled).
If you press button "
I
" immediately,
you will hear a prolonged beep and
the word "ON" will appear on the
display: the extra drying has been
enabled.
Once you have made your
selection, a beep will sound and
the wash cycle will either start
immediately or after the delay,
wherever set.
Remember that with extra drying,
the wash cycle will last longer, to
provide you with drier dishes.
You decide when it
starts.
When you have loaded the dishes,
you can choose when to start your
dishwasher before setting the wash
cycle desired. Press button "
P
"and
you can delay the start of the wash
cycle by 1 to 24 hours. Press the
button once, a beep will sound and
the wording "24 h" will come up on
the display. Then, each time you
press the button a beep will sound
and the hours will decrease by one
hour until the delay is 01 h. If you
press the button once again, the
delayed start is reset and 3 dashes
appear on the display.
Once you have set the delayed start
time, select the wash cycle on the
knob: after the beep sounds, you
will see indicator light "
H
" flash on
the display and the countdown
begins (indicated on the display one
hour at a time). A quick look at the
indicator lights will keep you
informed of the countdown
progress at all times.
Have you changed your
mind?
During the countdown, you can
modify the delay by pressing button
"
P
" repeatedly without resetting
the wash cycle.
If you have changed your mind and
wish to start the wash cycle
immediately, press button "
P
" until
the countdown is fully reset.
Indicator light "
H
" will turn off and
the cycle will start at the sound of
a beep.
Ready, steady, go!
The delayed start
is also reset
automatically
should you fail to
select the wash
cycle within 15
seconds.
Warning:
Turn the display off by pressing
button A, unplug the appliance
from the electricity socket to cut
off the power supply; the power
supply cable should
consequently be easily
accessible.
