Ariston LL 64, Instructions For Installation And Use Manual, Page: 8 / 16

4
ARISTON DISHWASHER - Instructions for installation and use
D
ISHWASHER
You have loaded your dishes and you now have to set the
wash cycle. It takes just one minute to learn how
Starting the dishwasher
Ready, steady, go!
First of all.
Turn on the water tap com-
pletely and press ON-OFF
button " A ". you will hear a short
beep and indicator light " B "
lights up. Now the appliance is
on and awaiting instructions.
Selecting the wash
cycle.
Select the wash cycle by
pressing button " P ". Each time
you press the button, a beep
will sound and indicator lights
" E " will light up in sequence:
choose the cycle you deem
most suited to the type of
dishes to be washed (take a
look at page 17, where you will
find the wash cycle table). If the
appliance door is shut, press
the Start button " R " and you will
hear a beep; the cycle will start
up within a few seconds.
The dishwasher informs
you.
Your dishwasher is fitted with
indicator lights ( G ) which light
up to indicate the cycle phase
under way.
Here are the symbols corre-
sponding to each cycle phase:
pre-wash, wash, rinses, drying.
At all times, your dishwasher
tells you which cycle phase is
under way.
Modifying a wash cycle
in progress.
But if you have chosen the
wrong cycle, not to worry! You
can modify the wash cycle in
progress, if it has only just
started. Keep the RESET
button " R " pressed for about 5
seconds: a prolonged beep will
sound, followed by three short
beeps. Indicator light " G " will
turn off and at this stage, all the
settings will have been
cancelled. You are now free to
re-set the correct wash cycle.
You've left out a dish?
Well, it happens to everyone.
Interrupt the wash cycle by
pressing the ON-OFF button,
insert the dish you had
forgotten and press the ON-
OFF button again. The cycle
will start up from where you
interrupted it.
Finished?
The end of the wash cycle is
indicated by two short beeps
and the flashing of the drying
phase indicator light.
CAUTION
Turn the display off by
pressing button “A”, unplug
the appliance from the
electricity socket to cut off
the power supply; the
power supply cable should
consequently be easily
accessible.
•
Turn off the water tap.
•
Wait a few minutes before un-
loading the dishes: they are
very hot! If you wait a little
while, they dry better thanks
to the steam.
•
Empty the lower rack first.
There's been a power
failure? Have you
opened the dishwasher
door?
The wash cycle stops and then
restarts when the electricity
comes back on or when you
shut the door. Everything is
under control!
You decide when it
starts.
When you have loaded the
dishes, you can choose when
to start your dishwasher before
setting the wash cycle desired.
Press button " D " to delay the
start of the wash cycle by 12, 9,
6 or 3 hours. Each time you
press it, you will hear a short
beep and the indicator light " G "
corresponding to the selected
delay will light up.
Now you can select the desired
wash cycle. Press the start but-
ton " R " and after you hear the
beep, the countdown to the de-
layed start will begin.
Once this time is up, the indi-
cator light will stop flashing and
the wash cycle will begin.
If you have set a 12 hour delay,
for example, once you have
selected the wash cycle, the 12
hour indicator light will flash
followed by the others in
sequence until the set time
delay is up. A quick look at the
indicator lights will keep you
informed of the countdown
progress at all times.
Have you changed your
mind?
If you change your mind, you
can set a shorter time delay:
press button " D " to select it. You
need not reset the wash cycle.
If on the other hand you want
to cancel the delay set and you
want the cycle to start
immediately, press button " D "
repeatedly until the cycle starts
and indicator light " G "
corresponding to the cycle start
phase comes on.
Dual function of
indicator lights "G"
1) flashing to indicate a
delayed start: to remind you
that you have set a delayed
start;
2) on and not flashing
beneath the cycle phase
symbol:
meaning the cycle has started
and is in the phase indicated by
the symbol.
You want to wash on
one rack only?
Remember to use half
the amount of
detergent.
If you only have a few dishes to
wash, you can decide to run a
half-load, to save on water,
electricity and detergent.
Before setting any wash cycle
whatsoever, press button " F ",
indicator light " H " will light up
and your dishwasher will wash
on the upper rack only.
Would you like to see
which settings you
have made?
At any time, when the cycle is
under way, if you press button
" P ", the cycle in progress
indicator light will light up for
a few seconds, followed by the
half load indicator light,
wherever set.
If opening the door
soon after the end of
the programme,or
during it, stand away
from the Dishwasher,
to avoid possible
injury from hot
steam.
Make sure the wash
cycle has ended
before removing the
dishes!