Ariston LD 87, Instructions For Installation And Use Manual

Page: 17 / 25

14
ARISTON DISHWASHER - Instructions for installation and use
D
ISHWASHER
You have loaded your dishes and you now have
to set the wash cycle. It takes just one minute
to learn how
Starting the dishwasher
Ready, steady, go!
First of all.
Insert the plug into the electricity
socket to power the dishwasher.
Turn on the water tap completely
and press the Stand-by button .
The display turns on and 4 dashes
appear: these indicate that the
dishwasher is awaiting instructions.
Selecting the wash cycle
Select the wash cycle
by pressing this button
Each time you press the button, a
beep will sound and the
corresponding symbols will light up
in sequence:
choose the cycle you deem most
suited to the type of dishes to be
washed (take a look at page 16,
where you will find the wash cycle
table). Keep the Start button
pressed for a few seconds and the
wash cycle begins, but if you have
left the dishwasher door open, the
word “DOOR” will be displayed;
shut it and press the same button
again.
A beep sounds and then the wash
cycle begins and only the symbol
corresponding to the wash cycle
selected is displayed.
You can see the amount of time
left until the end of the wash cycle
on the counter. Do not expect a
precise countdown as the wash
cycle starts with an estimated cycle
time that is updated, thanks to the
sensor it is fitted with, as the cycle
progresses, according to a number
of parameters that ensure
maximum wash efficiency.
The dishwasher keeps you
informed.
Your dishwasher is fitted with
indicator lights ( H ) which light up
to indicate the cycle phase under
way.
Here are the
s y m b o l s
corresponding to
each cycle phase:
At all times, your
dishwasher tells
you which cycle
phase is under
way.
Modifying a wash cycle in
progress.
But if you have chosen the wrong
cycle, not to worry! You can modify
the wash cycle in progress, if it has
only just started. Keep the Reset
button
pressed for about 2
seconds: a prolonged beep will
sound, followed by three short
beeps. Indicator light “I” turns off
and the 4 dashes appear to indicate
that all the settings have been
cancelled. You are now free to re-
set the correct wash cycle.
You’ve left out a dish?
Well, it happens to everyone.
Interrupt the wash cycle by
pressing the Stand-by button, insert
the dish you had forgotten and
press the same button again. The
cycle will start up from where you
interrupted it.
Finished?
The end of the wash cycle is
indicated by two short beeps and
the word “END” flashes on the
display.
• Turn the display off by pressing
button “A”, unplug the appliance
from the electricity socket to cut
off the power supply; the power
supply cable should consequently
be easily accessible.
• Turn off the water tap.
• Wait a few minutes before
unloading the dishes: they are very
hot! If you wait a little while, they
dry better.
• Empty the lower rack first.
There’s been a power
failure? Have you
opened the dishwasher
door?
The wash cycle stops and then
restarts when the electricity comes
back on or when you shut the door.
Everything is under control!
Have you left the
dishwasher door open?
The word “DOOR” flashes on the
display. Shut the appliance door and
the wash cycle will start up again.
“Duo Wash”
Cycle:
This is a special cycle that runs a
differentiated wash on the two
racks: delicate for glassware and
glasses on the upper rack and heavy
duty for saucepans and frying pans
on the lower rack.
Press the (Mode) button
and select the Duo-Wash symbol,
then press (Select): “on” means
it is selected and the corresponding
rectangle will light up, whereas
“off” means it is disabled; after
approx. 5 seconds, you will
automatically quit the menu. Now
press Start and the wash cycle starts
with a beep.
You decide when it starts.
When you have loaded the dishes,
you can choose when to start your
dishwasher before setting the wash
cycle desired.
Press button “M” (Mode) and then
select the symbol corresponding
to the delayed start:
the corresponding rectangle will
darken. Now press button “S”
(Select) to delay the wash cycle
start by 1 to 24 hours. If you press
the button again, the word “OFF” is
displayed (no selection made).
Each time the button is pressed, a
beep will sound; once you have
made your selection, make sure the
appliance door is shut and start the
wash cycle by pressing button
(START). The countdown to the
delayed start will begin on the
display.
Once the countdown is up, the
wash cycle begins and the
approximate amount of time left
until the end of the wash cycle is
displayed.
Have you changed your
mind?
If you change your mind and wish
to set a different delay press the
Mode and Select buttons and
repeat the selection.
If on the other hand you want to
cancel the delay set and you wish
to start the wash cycle
immediately, press the Select
button repeatedly until it is set to
zero. The following indicator light
will turn off:
Do you want extra
drying?
Before you start the selected wash
cycle, press button “M” (Mode)
repeatedly until the extra drying
symbol “G” is selected, and the
corresponding rectangle lights up.
Press button “S” (Select) and select
On to enable the extra drying, or
Off to disable it. Remember that
with the extra drying enabled, the
wash cycle will last longer to
provide you with dryer dishes.
This option is incompatible with
the soak cycle.
You want to wash
just half a load?
Remember to halve the
amount of detergent.
Have you only got a few dishes that
need washing? If so, load them all
on a single rack to save on water,
detergent and electricity. Press the
Mode button repeatedly until
symbol “N” is selected: the
corresponding rectangle will light
up. Using button S (select), you can
decide to wash a half-load on the
upper rack
or on the lower one .
Each time you press it, a beep will
sound and the corresponding
symbol will light up. The symbol
for the selected rack is displayed.
Off means “no selection” has been
made
Once you have made your
selection, start the wash cycle by
pressing START.
This option is available with all
wash cycles.
Prelavaggio
Lavaggio
Risciacqui
Asciugatura
The delayed start
is also reset
automatically
should you fail to
select the wash
cycle within 15
seconds.
P
Make sure the wash
cycle has ended before
removing the dishes!