19
GB
Service
Tr
oubleshooting
Precautions
Care
Programmes
Detergents
Installation
Description
Using the Drilling Template.
- To trace the positions of the holes on the left-hand side
of the panel, align the drilling template to the top left side
of the panel using the lines traced on the extremities as a
reference.
- To trace the positions of the holes on the right-hand
side of the panel, align the drilling template to the top
right side of the panel.
- Use an appropriately sized router to mill the holes for
the two hinges, the rubber plug and the magnet.
Mounding the Parts onto the Wooden Panel (Door).
- Insert the hinges into the holes (the movable part of the
hinge must be positioned facing away from the panel) and
fasten them with the 4 type
A
screws.
- Insert the magnet into the top hole on the opposite side
of the hinges and fasten it with the two type
B
screws.
- Insert the rubber plug into the bottom hole.
The panel is now ready to be mounted onto the machine.
Mounting the Panel into the machine.
Insert the nib of the hinge (indicated by the arrow in
fig. 2
)
into the hole for the hinge and push the panel towards the
front of the machine. Fasten the two hinges with the type
D
screws.
Fastening the plinth guide.
If the machine is installed at the end of a set of modular
cabinets, mount either one or both of the guides for the
base molding (as shown in
fig. 8
). Adjust them for depth
based on the position of the base molding, and, if
necessary, fasten the base to the guides
(fig. 9)
.
This is how to assemble the plinth guide
(fig. 8)
:
Fasten angle
P
using screw
R
, insert plinth guide
Q
into
the special slot and once it is in the desired position, lock
it in place using angle
P
and screw
R
.
Inserting the machine into the Cabinet.
- Push the machine into the opening, aligning it with the
cabinets
(fig. 6)
.
- Regulate the adjustable feet to raise the machine to the
appropriate height.
- To adjust the position of the wooden panel in both the
vertical and horizontal directions, use the
C
and
D
screws, as shown in
fig. 7
.
Important:
close the lower part of the appliance front by
ensuring that the plinth rests against the floor.
Fig. 8
Fig. 9
Accessories provided for the height adjustment.
The following can be found inside the polystyrene lid
(fig. 10)
:
2 crossbars (
G
), 1 strip (
M
)
the following can be found inside
the appliance drum:
4 additional feet (
H
),
4 screws (
I
),
4 screws (
R
),
4 nuts (
L
),
2 plinth guides (
Q
)
Adjusting the appliance height.
The height of the appliance can be adjusted (from
815
mm
to
835
mm), by turning the
4
feet.
Should you require the appliance to be placed higher than
the above height, you need to use the following accessories
to raise it to up to
870
mm:
the two crossbars (
G
); the 4 feet (
H
); the 4 screws (
I
); the 4
nuts (
L
) then perform the following operations
(fig. 11)
:
remove the
4
original feet, place a crossbar
G
at the front of
the appliance, fastening it in place using screws
I
(screwing
them in where the original feet were) then insert the new feet
H
.
Repeat the same operation at the back of the appliance.
Now adjust feet
H
to raise or lower the appliance from
835
mm to
870
mm.
Once you have reached the desired height, lock nuts
L
onto
crossbar
G
.
To adjust the appliance to a height between
870
mm and
900
mm, you need to mount strip
M
, adjusting feet
H
to the
required height.
Insert the strip as follows:
loosen the three screws
N
situated at the front of the Top
cover of the appliance, insert strip
M
as shown in
fig. 12
,
then fasten screws
N
.
D
C
C
570
min
815
540
595
820 ÷ 900
600 min
Fig. 6
Fig. 7
L
I
H
G
M
Fig. 11
Fig. 12
Fig. 10
