Ariston AXD 100, Instructions For Installation And Use Manual

Page: 6 / 88

M
ARGHERITA
Margherita - Instructions for installation and use
To use this, press the Select
button until the On sign comes on.
During a wash cycle, the
selectionof this option is indicated
by symbol coming on.
This option is available on
programmes 2-3-5-6-7-8-10 and
Rinse cycles .
Note : It must not be used with the
Easy iron option.
Easy iron
This function allows your
washing to come out of the
machine without creases,
making it much easier to iron .
The appliance optimises the
washing conditions according to
the type of fabrics that are being
washed.
It is enabled with programmes
3-5-6-7-8-11 and Rinse cycles .
To enable it, press the Select
button until the On sign comes on.
In programmes 6-7-8-11 and
Light Rinse cycles , the wash
cycle is interrupted and the
washing is left to soak in water
before the appliance is drained.
To complete the cycle, press the
Select button.
During a wash cycle, the enabling
of this option is indicated by
symbol coming on.
Note : It must not be used with
the Stain removal option.
Rinse level
This increases the efficiency of
the rinse. We recommend that you
use it when dealing with a full
load and a great amount of
detergent.
There are three levels; press the
Select button to select them.
Low
Medium
High
This option is available on
programmes 1-2-3-4-5-6-7-8 and
Rinse cycles .
Note: Function is disabled.
E
A
B
C
D
F G
Mode Select
Here I’m in command
Understanding the control panel
Making the right choice is important. And it’s easy.
Margherita’s knobs
are hidden. Just
press them lightly in
the middle to
extract them.
The detergent dispenser with
the additional bleach
compartment is here.
3
MAX
1
2
4
3
Spin variation
The display indicates the maximum
speed relating to the programme
set, which can be reduced by
pressing the Select button right
down to its total exclusion ( Off ).
During a wash cycle, the selection
of the spin cycle exclusion is
indicated by symbol coming
on.
This option is available on all
wash programmes except for
number 11 and Drain .
Wash intensity
This allows you to modify the
characteristics of the selected wash
programme, according to how
soiled the washing is. There are
three levels; press the select button
to Select them.
Low
Medium
High
This option is available on
programmes 1-2-3-5-6-7-8 .
Delay timer
This allows you to delay the start
of the wash cycle by a minimum
of 1 to a maximum of 24 hours
by pressing the Select button.
The enabling of the delayed start
is indicated by the symbol
coming on and staying on until
the wash cycle begins.
This option is not available on the
Drain and Spin cycle
programmes.
Stain removal (see page 7)
Thanks to this command, the
washing machine will carry out a
more intensive wash that optimises
the effectiveness of the liquid
additives, thus allowing more
resistant stains to be removed.
Programme selector knob
To select a programme, you
should turn the knob so that the
symbol/number of the desired
programme is in line with the
pointer on the glass G .
On-off
When button B is pressed, the
washing machine is switched on,
when it is not the machine is
switched off.
Turning the appliance off does
not cancel the selected
programme.
When the appliance is switched
on, all the symbols on the display
light up for at least 8 seconds,
after which only the ones that
can be selected will flash.
Start /Reset
This button allows you to start
the selected wash programme or
to interrupt it.
If you press it briefly, the button
functions as Start , if you press
it for at least 3 seconds, then it
functions as Reset .
After the Start of the appliance,
moving the programme selector
knob will have no effect
whatsoever.
Detergent dispenser
It is divided into three
compartments:
1. Detergent for pre-wash;
2. Detergent for the main cycle
wash;
3. Fabric conditioner.
The washing machine is
equipped with an extra
compartment 4 (provided as an
accessory) for the bleach, to be
inserted in compartment 1 .
Programme key
This contains the descriptions of
the wash programmes and the
various functions connected to
the buttons. Pull it outwards to
open it.
Display
All the options available are
displayed on the right-hand side.
Use the Mode button to select
the desired option, and the rela-
tive symbol will begin flashing.
On the left-hand side, the value
or the status ( On-Off ) of the
selected option is displayed, and
you can modify it using the
Select button.
To access the subsequent option,
press the Mode button,
otherwise press button C (Start/
Reset) to start the wash cycle.
All the options available are
listed below.
Only options relevant to the
selected programme will be
displayed.
Temperature
The display indicates the
maximum temperature relating
to the programme set, which can
be reduced by pressing the
Select button right down to cold
wash ( Off ).
This option is available on all
wash programmes.