Instructions for installation and use
www.aristonappliances.us
I
G
L
F
E
H
N
M
A
B
C
D
Temperature control knob
It is used to set the wash tem-
perature in the recommended
program table on pg. 11. It also
allows you to reduce the tem-
perature recommended for the
selected program, and even to
set a cold wash cycle.
ON-OFF (Power)
To turn on the washer-dryer,
press button
L
in. To turn off,
press button I again so that it
is out.
Turning the appliance off
does not cancel the selected
program.
On-Off lamp -
Door lock (Status)
Lamp
M
flashes slowly when
the appliance is switched on
and awaiting instructions and
at the end of a cycle, indicating
that the door can be opened. It
flashes quickly when the door
should not be opened. A
steady light means the
appliance has accepted the
selected programme.
Drying cycle lamp
When this lamp is on, it means
that knob
C
has been set on a
drying cycle and at the end of
the wash cycle, the appliance
will run the selected tumble
drying cycle.
Easy iron
This function allows your
clothes to come out of the
machine without wrinkling,
making it much easier to iron.
You can use it with
Permanent Press
and
Hand
Washables
programs.
Press this button in such
programs and the wash cycle
will come to a stop on one
position
Easy iron
.You can
complete the cycle by pressing
button
H
again.
Dry Time knob
This control allows you to
preset the drying time you want
according to your require-
ments which may be “
damp
dry
” ready for ironing, or “
bone
dry
” ready for putting away. For
more details see the drying
time table on page 12. After all
the controls have been
correctly set, the dryer will start
to operate as soon as you close
the door.
Washer knob and Delay
start
Use this knob to select the
wash program.
Turn this knob clockwise only.
To select a program, you should
turn the knob so that the word/
number of the desired program
is in line with the pointer on the
knob.
Now press on/off button
L
(position
I
), pilot lamp
M
will
start flashing.
After 5 seconds, the setting will
be accepted, pilot lamp
M
will
stop flashing (staying lit) and the
wash cycle will begin.
If you want to interrupt the
program in progress or set a new
one, select one of the
Reset
positions and wait 5 seconds
.
When the cancellation has
been accepted, pilot lamp
will
flash 5 times, and you can then
turn the appliance off.
You can use this knob to delay
the appliance's operation.
Select one of the 4 delay time
positions, press the on/off
button
L
in and wait 5 min. The
setting has now been accepted
(pilot lamp
M
stays lit) and you
can select the program you
desire.
Pilot lamp
M
has a particular
flashing motion (2" on and 4"
off) to indicate that a delayed
start has been set.
During this phase, you can
open the appliance door and
change the washing load,
should you wish to do so.
After the wash cycle has been
set and accepted by the
washer-dryer, turning the knob
will have no effect (except for
when it is on position
Reset
(Stop).
Detergent dispenser
It is divided into
3+1
sections:
1.
Detergent for pre-wash;
2.
Detergent for the main
cycle wash;
3.
Fabric conditioner;
4.
Bleach.
Here I’m in control
Extra Rinse
This function adds one rinse
cycle
for Cotton and
Permanent Press
fabrics.
Use of this function is
recommended for improving
rinsing results when washing
full loads and large quantities
of detergent are used.
Recommended in case of
detergent contact allergies.
Low Spin
Use this button to reduce the
spinning speed from 1200 to
600 rpm for the cotton and
linen programs and from 850
to 450 rpm for the Permanent
Press fabrics programs.
The detergent dispenser with
the additional bleach
compartment is here.
(For details see page 15).
Knobs are hidden.
Just press them lightly in the
middle to extract them.
Making the right choice is important. And its easy.
Program key
to consult a
straightforward chart of the
different programmes availa-
ble: pull the grey tab outwards
to open it.
Pre-wash
With this button, you can pre-
wash on all programs except
the Wool program. (see page
11).
Note:
If you run a dry cycle,
pressing this button the
machine will not carry out the
easy iron function.
MAX
1
2
4
3
10
