Manual abstract:
Read these instructions carefully: they contain vital information on installation, use and safety. Levelling your appliance correctly will provide it with
stability and avoid any vibrations, noise and shifting during operation. If it is placed on a fitted or loose carpet, adjust the feet in such a way as to allow
enough room for ventilation beneath the washing machine. Unpacking and levelling Unpacking Electric and water connections Connecting the water inlet
hose 1. Unpack the washing machine. 2. Check whether the washing machine has been damaged during transport. If this is the case, do not install it and
contact your retailer. 3. Remove the four protective screws and the rubber washer with the respective spacer, situated on the rear of the appliance (see
figure).
4. Seal the gaps using the plastic plugs provided. 5. Use the plug provided to seal the three holes where the plug was housed, situated on the lower right-hand
side on the rear of your appliance. 6.
Keep all the parts: you will need them again if the washing machine needs to be moved to another location. 1. Connect the supply pipe to the water mains
using a gas 3/4 attachment, fitting the rubber gasket and the filter supplied with the appliance and ensuring that they are fimly tightened to the taps. The water
supply marked C must be connected to the cold water tap; the pipe marked H must be connected to the hot water tap. Both pipes may be connected to the cold
water tap using the special Y connection with multiple attachments, supplied with the appliance (see figure).
Before making the connection, allow the water to run freely until it is perfectly clear. Packaging materials are not children's toys. Levelling 1. Install the
washing machine on a flat sturdy floor, without resting it up against walls, furniture cabinets or other. 2. If the floor is not perfectly level, compensate for any
unevenness by tightening or loosening the adjustable front feet (see figure); the angle of inclination, measured according to the worktop, must not exceed 2°.
2. Connect the other end of the water inlet hose to the washing machine, screwing it onto the appliance's cold water inlet, situated on the top right-hand side
on the rear of the appliance (see figure). 3. Make sure there are no kinks or bends in the hose.
The water pressure at the tap must be within the values indicated in the Technical details table (on the next page). If the water inlet hose is not long
enough, contact a specialist store or an authorised serviceman. 2 Connecting the drain hose 65 - 100 cm Connect the drain hose, without bending it, to a
draining duct or a wall drain situated between 65 and 100 cm from the floor; When the washing machine is installed, the mains socket must be within easy
reach. Do not use extensions or multiple sockets. The power supply cable must never be bent or dangerously compressed. The power supply cable must
only be replaced by an authorised serviceman. Warning! The company denies all liability if and when these norms are not respected. GB Installation
Description alternatively, place it over the edge of a basin, sink or tub, fastening the duct supplied to the tap (see figure). The free end of the hose should not
be underwater. The first wash cycle Once the appliance has been installed, and before you use it for the first time, run a wash cycle with detergent and no
laundry, setting the 90°C programme without a pre-wash cycle.
Programmes Detergents We advise against the use of hose extensions; in case of absolute need, the extension must have the same diameter as the original
hose and must not exceed 150 cm in length. Electric connection Technical details Model AVXL 129 59.5 cm wide 85 cm high 56,5 cm deep from 1 to 7,5 kg
voltage 230- 240 Volts 50 Hz maximum absorbed power 2050 W Precautions Before plugging the appliance into the mains socket, make sure that: Â the
socket is earthed and in compliance with the applicable law; Â the socket is able to sustain the appliance's maximum power load indicated in the Technical
details table (on the right); Â the supply voltage is included within the values i ndicated on the Technical details table (on the right); Â the socket is
compatible with the washing machine's plug.
You're reading an excerpt. Click here to read official HOTPOINT
AVXL 129 user guide
http://somemanuals.com/dref/4691435