6
GB
!
The manufacturer declines any liability should
these safety measures not be observed.
Gas connection
!
This appliance is suitable for use with
This appliance is suitable for use with
This appliance is suitable for use with
This appliance is suitable for use with
This appliance is suitable for use with
either a flexible connection or rigid copper
either a flexible connection or rigid copper
either a flexible connection or rigid copper
either a flexible connection or rigid copper
either a flexible connection or rigid copper
connection.
connection.
connection.
connection.
connection.
Check The Gas Type
WARNING: Before installation, check that the gas
suitable for the gas type available to the installation.
It is extremely dangerous to use the wrong gas type
with any appliance, as fire or serious injury can
result.
This cooker is supplied from the factory already set
for Natural Gas. To convert the cooker to LPG (or
back to Natural Gas from LPG), follow the directions
later in this section.
Fit regulator supplied for Natural Gas (if applicable)
at rear of appliance, and as close as practicable to
It is recommended that an isolating valve and union
be fitted, to enable simple disconnection for
servicing. These are to be in an accessible location.
!
Check that the pressure of the gas supply is
consistent with the values indicated in the “Technical
specifications”, p6. This will ensure the safe
operation and durability of your appliance while
Gas connection using a flexible rubber hose
Make the connection
using a gas hose that
complies with
requirements set forth
by the current National
Regulations. The
appliance is factory set
for connection to a
natural gas supply. A
fitting "
R
" with a conical
thread ISO7-1 (1/2 gas)
and a seal "
G
" is fitted at the end "
L
" of the pipe to
be connected to the gas mains. This fitting should
not be removed. When the connection pipe (flexible
or rigid) is dismounted, the fitting "
R
" should be
locked in place using a spanner before unscrewing
the metal pipe bolt. This is to prevent the fitting "
R
"
from slipping and so as not to cause any leaks from
sleeve "
L
". If the appliance is designed for left and
right gas connection, the cap should be inverted
and the seal supplied with the appliance should be
replaced when changing the connection.
If a flexible hose is used, it should be as short as
• the flexible connection must be approved to class
B or D of AS/NZS1869 as a minimum.
• it should not be bent, kinked or compressed;
• it should not be in contact with the rear wall of the
appliance or in any case with parts which may
reach a temperature of 50°C;
• it should not come into contact with pointed parts
or sharp corners;
• it should not be subject to any pulling or twisting
forces;
• it should be easy to inspect along its entire length
in order to be able to check its condition.
• The supply connection point must be accessible
with the appliance installed.
• The inner diameters of the pipe are as follows:
8 mm for LPG; 13 mm for Natural Gas.
Upon completion of installation, check the gas
circuit, the internal connections and the taps for
leaks using a soapy solution (never a flame). Also
check that the connecting pipe cannot come into
contact with moving parts which could damage or
crush it. Make sure that the natural gas pipe is
adequate for a sufficient supply to the appliance
when all the burners are lit
Connecting a flexible jointless stainless steel
pipe to a threaded attachment
Make sure that the hose and gaskets comply with
current national legislation.
To begin using the hose, remove the hose holder on
the appliance (the gas supply inlet on the appliance
is a cylindrical threaded 1/2 gas male attachment).
!
Perform the connection in such a way that the hose
making sure that the hose is not compressed and
does not come into contact with moving parts.
Checking the tightness of the connection
Upon completion of installation, check the gas
circuit, the internal connections and the taps for
leaks using a soapy solution (never a flame). Also
check that the connecting pipe cannot come into
contact with moving parts which could damage or
crush it. Make sure that the natural gas pipe is
adequate for a sufficient supply to the appliance
when all the burners are lit.
L
G
R
type (natural gas or LPG/
Universal
of the cooker is
possible with a maximum length of 1.
2
metres;
length does not exceed a maximum of
1.
2 metres,
the appliance.
maintaining efficient energy consumption.
the inlet connection.
ULPG test point adaptor is supplied and must be fitted to
Natural gas test point is located on the regulator
