ARIETE Hot Aquapower 4240, Instructions For Use Manual

Page: 18 / 38

- 16 -
EN
Fabric cleaning nozzle
⑩
and bristled attachment
⑪
This is particularly suited for cleaning surfaces such as armchairs, rugs, and smaller-sized hard surfaces, and also for fabrics
and curtains. It can be fitted to the hand grip
①
or tube
⑬
. The bristled attachment
⑪
can be fitted to the nozzle
⑩
; and it
is recommended for cleaning small-sized fabric surfaces (
16
).
Kit for cleaning glass and windows
⑫
Ideal for large glass surfaces, large mirrors, and smooth surfaces in general. It can be fitted to the hand grip
①
or tube
⑬
.
To use the glass washer correctly, proceed as follows:
• Evenly dispense the detergent over the surface to be cleaned so as to dissolve the dirt.
• Press the rubber scraper over the surface to be cleaned, moving it in vertical strokes from top to bottom, with the suction
function on.
CLEANING AND MAINTENANCE
In the interests of hygiene, after using the appliance, rinse out the attachments by vacuuming up clean water. In this way the
attachments and the inside of the hose will be cleaned.
In this way the attachments and the inside of the hose will be cleaned. Use a damp cloth to wipe the outside of the appliance
clean. Do not use solvents or detergents that could damage the plastic surfaces.
A few simple maintenance operations are necessary to make sure that the appliance will always operate perfectly.
Emptying and cleaning the dirty water container (G)
The dirty water container (G), must be emptied as soon as the red light (Q) switches on.
WARNING: As soon as the red light switches on, the motor will switch off automatically; after emptying the
container, press the on/off switch (N) to restart the appliance.
• Open the appliance cover (D) as described previously
• Take the dirty water container (G) by both handles (H), and remove it from the appliance body (
17
).
WARNING: Do not remove the lid (M) from the container before reaching the place where it is to be emptied;
this is to avoid any liquid spills while carrying it.
• As soon as you are ready, remove the cover (M) and empty out the container (G) upouring from the narrowest edge. Clean
out the container with water and a mild soap. Rinse the “Magic filter” thoroughly under running water (
18
).
• Follow these steps in reverse order to refit the container in the appliance, pressing down on it slightly to make sure it is
correctly in place (
19
).
Emptying the water and detergent container (X)
When not using the appliance for any length of time, take out and empty the water and detergent container so as to prevent
the formation of scale residues, which could affect the normal operation of the appliance.
Double air exhaust filter (Y
)
Remove the grille of the HEPA filter on the back of the appliance, pressing the top clip at the same time. Take out the filter
and if necessary, wash it in running water and then leave to dry completely. Refit the grille, pressing it gently until it clicks
into place (
20
).
Motor air filter (J)
Open the appliance cover (D) and take out the dirty water container (G) complete with lid (M), s previously described, using
the two handles (H). Remove the air filter (J) and clean it under running water. Leave it to dry perfectly before refitting it
inside the appliance (
21
).
“Magic Filter” (L)
Open the appliance cover (D) as described previously, and take out the water filter (M) by the special hand grip (
22
).
• Remove the filter cover (I) by gently pulling it downwards (L) and take out the protective filter (
23
).
• Rinse the “Magic filter” thoroughly under running water and leave to dry perfectly before fitting it together with the other
parts, following the above steps in reverse order.
WARNING: The filter(L) should be cleaned after every use and if it appears to be worn, it should be
replaced with the spare filter provided.