Ariens Sno-Tek 03883300A Owner'S/Operator'S Manual Download Page 2

GB - 2

SAFETY  . . . . . . . . . . . . . . . . . . . . . . . . .  4

ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . .  8

CONTROLS and FEATURES. . . . . . . . .11

OPERATION . . . . . . . . . . . . . . . . . . . . .  12

MAINTENANCE . . . . . . . . . . . . . . . . . .  16

SERVICE AND ADJUSTMENTS  . . . . .  18

STORAGE  . . . . . . . . . . . . . . . . . . . . . .  27

SERVICE PARTS . . . . . . . . . . . . . . . . .  27

ACCESSORIES  . . . . . . . . . . . . . . . . . .  27

TROUBLESHOOTING . . . . . . . . . . . . .  28

SPECIFICATIONS  . . . . . . . . . . . . . . . .  29

WARRANTY . . . . . . . . . . . . . . . . . . . . .  30

NON-ENGLISH MANUALS

Manuals in languages other than English may 
be obtained from your dealer. Visit your 
dealer or www.ariens.com for a list of 
languages available for your equipment.
Manuals printed in languages other than 
English are also available as a free download 
on our website:

http://www.ariens.com

MANUALES EN IDIOMAS 
DIFERENTES DEL INGLES

Puede obtener manuales en idiomas 
diferentes del inglés en su distribuidor. Visite 
a su distribuidor o vaya a www.ariens.com 
para obtener una lista de idiomas disponibles 
para su equipo.

También puede imprimir manuales en 
idiomas diferentes del inglés descargándolos 
gratuitamente de nuestra página Web:

http://www.ariens.com

MANUELS NON ANGLAIS

Des manuels dans différentes langues sont 
disponibles chez votre revendeur.  Rendez-
vous chez votre revendeur ou allez sur le site 
www.ariens.com pour consulter la liste des 
langues disponibles pour votre équipement.

Les manuels imprimés dans des langues 
différentes de l'anglais sont également 
disponibles en téléchargement gratuit sur 
notre site Web :

http://www.ariens.com

MANUALS

Before operation of unit, carefully and 
completely read your manuals. If used 
improperly, this unit could be dangerous and 
cause personal injury or property damage. 
The contents will provide you with safety 
instructions for the safe use of your unit 
during normal operation and maintenance.

All reference to left, right, front, or rear are 
given from operator standing in operation 
position and facing the direction of forward 
travel.

ENGINE MANUAL

The engine on this unit is covered by a 
separate manual specific to the engine. This 
manual is included in the literature package 
that shipped with the unit. Refer to this 
manual for engine service recommendations. 
If the engine manual is not available, contact 
the engine manufacturer for a replacement 
manual.

MODEL AND SERIAL NUMBERS

When ordering replacement parts or making 
service inquiries, know the Model and Serial 
numbers of your unit and engine.
Numbers are located on the product 
registration form in the unit literature 
package. They are printed on a serial number 
label, located on the frame of your unit.

TABLE OF CONTENTS

INTRODUCTION

Figure 1

Serial Number Label

OS8010

Summary of Contents for Sno-Tek 03883300A

































Reviews: